Table of Contents
Advertisement
LCD display
A
Sleep / Snooze indicator
B
Alarm 1
C
Alarm 2
D
Bluetooth icon
E
RDS indicator
F
FM Stereo indicator
G
Menu indicator
H
Signal level indicator
I
Frequency / Text display
J
Time display
K
PM time indicator
GB
Preparing the remote control
The radio's remote control requires two AAA batteries to
operate. To place the batteries:
1.
Open the battery compartment on the back of the
remote control.
2.
Insert two AAA batteries in the battery compartment with
polarities as shown in the diagram inside the battery
compartment.
3.
Close the battery compartment again.
Using the AC power adapter
The AC / DC Switching adapter supplied with this unit
has an output of 19V-1.8A center pin positive. Insert
the adapter plug into the DC socket on the rear of the
radio. Plug the adapter into a standard AC outlet. The AC
adapter should be disconnected from the AC outlet when
not in use for long periods of time.
IMPORTANT:
The AC adapter is used as the means of connecting the
radio to your power supply. The AC adapter used for the
radio must remain accessible during normal use. In order
to disconnect the radio from the power supply completely,
the AC adapter should be removed from the power supply
outlet completely.
Listening to DAB radio
Tuning into DAB stations
To tune into DAB radio stations, follow these steps:
1.
Fully extend the telescopic antenna located on the rear
of your radio.
2.
Press the Power button to turn on the radio.
3.
Select the DAB radio mode by repeatedly pressing the
Mode button.
4.
If this is the first time the DAB radio mode is being used,
the radio will automatically perform a full scan in order
to find all available DAB radio stations. If the radio has
been used before the last used station will be selected.
5.
During the scanning process, as new stations are
04
detected the station counter will increase and the
stations will be added to the list which is stored in the
radio.
6.
When the scanning is completed, the first station will be
selected. Rotate the Tuning knob to access the radio
station list and scroll through the available stations.
Then press the Tuning knob to tune into a station.
7.
Rotate the Volume knob to set the sound level as
needed.
The DAB radio menu
You can enter the DAB radio menu by pressing and
holding the Info / Menu button while the radio is in the
DAB radio mode.
Rotate the Tuning knob to select one of the options, then
press the Tuning knob to confirm your choice. To exit
menu options, press the Info / Menu button.
The radio's default and recommended settings are
indicated using an asterisk.
The DAB radio menu offers the following options:
● [Full Scan]: Select this option to perform a full scan
and store all DAB radio stations that were found in the
station list.
● [Manual Tune]: Select this option to manually tune into
a DAB channel / frequency.
● [Station Order]: Select this option and subsequently
se le ct [Alphanumeric] to so rt the stati on li st
alphanumerically, select [Ensemble] to sort the station
list by DAB multiplex, or select [Active] to sort the
station list by active / inactive stations.
● [Prune Invalid]: Select this option to delete all
unavailable stations from the station list.
● [DRC]: Dynamic Range Control (also known as DRC)
can make quieter sounds easier to hear when your
radio is used in a noisy environment by reducing the
dynamic range of the audio signal.
After selecting this option, select the desired DRC
setting:
[Off]: DRC is switched off. Broadcast DRC will be
ignored. This is the default setting.
[Low]: DRC level is set to 1 / 2 that sent by broadcaster.
[High]: DRC is set as sent by broadcaster.
NOTE: Not all DAB broadcasts are able to use the DRC
function. If the broadcast does not support DRC, then
the DRC setting in the radio will have no effect.
● [System Settings]: Select this option to go to the
system settings menu and configure the radio (refer
to the chapter "Using the system settings menu" for
details).
Showing DAB information on the display
When listening to a DAB radio broadcast, repeatedly
press the Info / Menu button to cycle through the
following information on the radio's display:
Scrolling text (DLS), Program type, Multiplex name,
Channel & frequency, Bit rate & audio type, Signal
strength, Date.
Advertisement
Table of Contents
