Related Manuals for Vivo DESK-V037KF
Summary of Contents for Vivo DESK-V037KF
- Page 1 Desk Riser SKU: DESK-V037KB SERIES DESK-V037KN DESK-V037KB DESK-V037KW DESK-V037KA DESK-V037KF Instruction Manual Assembly Video & Product Info https://vivo-us.com/products/desk-v000k...
- Page 2 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
-
Page 3: Package Contents
Package Contents A (x1) B (x1) C (x1) Desk Keyboard Tray Stopper D (x3) E (x4) F (x2) Rubber Feet Cable Clip Included Hardware & Tools S-B (x4) S-A (x2) M5x10mm Screw ST4.2x12mm Screw Tools Needed: Weight Capacity: 33lbs (15kg) Phillips Scissors Screwdriver... -
Page 4: Assembly Steps
ASSEMBLY STEPS STEP 1 Apply Pads (D) to underside of Keyboard Tray (B). Assemble Stopper (C) to Kayboard Tray (B) using ST4.2x12mm Screws (S-A) and a Phillips screwdriver. S-A (x2) STEP 2 Install Rubber Feet (E) to the bottom of Desk (A). Remove shipping tie from desk and set right side up on solid surface. - Page 5 STEP 3 Raise Desk (A) by lifting the handle on the right side of the frame. Place Keyboard Tray (B) on the metal brackets on Desk (A). Secure Keyboard Tray (B) to brackets using M5x10mm Screws (S-B) and tighten with a Phillips screwdriver. S-B (x4)
- Page 6 STEP 4 Apply Cable Clips (F) to underside of Desk (A). Desk riser is now ready for use Press side lever to raise or lower your desk riser. When lowering without any weight on the desktop, lightly press down on riser as you lower it to allow for a smoother lowering process.
- Page 7 GROMMET MOUNT USE This desk riser features a pre-drilled grommet hole for installing a monitor mount directly to desk surface. To utilize this feature, your will need to remove the plug from the top surface of the riser. Secure your mount using a grommet mounting method, using the hardware and assembly steps from your monitor mount.
-
Page 8: Tension Adjustment
TENSION ADJUSTMENT If your desk riser lifts up or down too easily, or is too difficult, the gas spring cable can be adjusted to your desired tension. The adjustment is located at the base of your riser. Start by loosening the Upper (1) and Lower (2) Nuts using an adjustable wrench. Loosen Nuts until they are both on the opposite ends of the Gas Spring Cable. - Page 9 TENSION CONT’D Option A: Desk Is Difficult to Raise/Lower | Increase Tension If the desk feels difficult to raise and lower, you will need to increase the Gas Spring Cable tension. Gently pull the cable away from the Lever until the Inner Nut (2) is firmly pressed against the middle divider.
- Page 10 TENSION CONT’D Option B: Desk Raises/Lowers Too Easily | Decrease Tension If the desk is raising or lowering without the handle being pressed, the tension will need loosened. Gently push the cable down towards the base of the riser until the Upper Nut (1) is firmly pressed against the middle divider.
- Page 11 CAUTION! Keep monitor and Follow the cable Leave enough slack Raise desktop laptop base fully on routing instructions to in cable to allow for slowly to keep the desktop. avoid the potential to full range of vertical items stable. pinch cables. motion (15”...
- Page 12 LAST UPDATED: 10/03/2023 REV2 Need Help? Get In Touch Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com www.vivo-us.com 309-278-5303 Chat live with an agent! FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us...