Advertisement
Quick Links
Desk Riser with Dual Monitor Mount
Instruction Manual
SKU: DESK-V042KB-M2
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/desk-v000k-m2
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
Advertisement
Related Manuals for Vivo DESK-V042KB-M2
Summary of Contents for Vivo DESK-V042KB-M2
- Page 1 Desk Riser with Dual Monitor Mount Instruction Manual SKU: DESK-V042KB-M2 Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/desk-v000k-m2 GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com...
-
Page 2: Pinch Point
WARNING! If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. -
Page 3: Package Contents
PACKAGE CONTENTS E (x4) D (x3) A (x1) B (x1) C (x1) Rubber Feet Desk Keyboard Tray Stopper H (x1) F (x2) G (x1) Pole Cable Clip Swivel Arm M (x1) I (x2) J (x1) K (x1) L (x1) Pole Cable VESA Plate Grommet Clamp... -
Page 4: Assembly Steps
ASSEMBLY STEPS STEP 1 Apply Pads (D) to underside of Keyboard Tray (B). Assemble Stopper (C) to Kayboard Tray (B) using ST4.2x12mm Screws (S-A) and a Phillips screwdriver. STEP 2 Install Rubber Feet (E) to the bottom of Desk (A). Remove shipping tie from desk and set right side up on solid surface. - Page 5 STEP 3 Raise Desk (A) by lifting the handle on the right side of the frame. Place Keyboard Tray (B) on the metal brackets on Desk (A). Secure Keyboard Tray (B) to brackets using M5x10mm Screws (S-B) and tighten with a Phillips screwdriver.
- Page 6 STEP 4 Install the Pole Cap (O) onto the top of the Pole (H). STEP 5 Remove the grommet cap from the top of the Desk (A). Grommet Remove adhesive cover and install the Rubber Pads (P) onto the underside of the Grommet Plate (J) in an even, circular pattern.
- Page 7 STEP 6 Place the Pole (H) onto the Grommet Plate (J). Slide Support Plate (L) onto Clamp Bolt (K), then thread Bolt through mounting hole in Desk (A), anchoring into Pole with Grommet Plate. STEP 7 Slide Pole Cable Clip (M) and Swivel Arm (G) onto Pole (H). Secure Swivel Arm in place using 6mm Allen Wrench (T-A).
- Page 8 STEP 8 Flat Back Monitors For flat back monitors, install VESA Plates (I) to monitors using appropriate Screws (M-A, M-C), M5 Washers (M-E) and a Phillips screwdriver, being careful not to overtighten. Recessed Back Monitor Install VESA Plates (I) to monitors using appropriate Screws (M-B, M-D), M5 Washers (M-E), Spacers (M-F) and a Phillips screwdriver, being careful not to overtighten.
- Page 9 STEP 9 Slide monitors onto Swivel Arm (G). Place Knobs (S-D) on VESA Plates (I) and secure using M3x8 Screws (S-C) and a Phillips screwdriver. STEP 9 Adjust monitor tilt by using the 6mm Allen Wrench (T-A) to loosen and tighten the joint.
- Page 10 STEP 10 Manage cables using Arm Cable Clips (N) and Pole Cable Clip (M). Apply Cable Clips (F) to underside of Desk (A) and route cables.
- Page 11 ADJUSTMENTS Adjust the height of the monitor by loosening Knob (S-D) with 6mm Allen Wrench (T-A). Place the 6mm Allen Wrench in into the Pole Cable Clip (M) for quick access. Position the monitors into a comfortable viewing orientation. WARNING To prevent tipping, please be careful not to extend the arms too far forward or backward.
- Page 12 : 1HR 8M (within office hrs) - 23% within < 15m - 38% within < 30m - 61% within < 1hr - 83% within < 2hr - 92% within < 3hr FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com...