Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crown PRO-INS24N1
Summary of Contents for Crown PRO-INS24N1
- Page 1 INSERT MOUNT INSTRUCTION MANUAL Model No.: PRO-INS24N1 PRO-INS30N1 PRO-INS36N1 C R O W N R A N G E H O O D S ALL FORWARD GROUP CORP. TEL: (416) 883-2441, Fax: (416) 247-7700 5940 Shawson Dr, Mississauga Ontario Canada M9W 1B4...
- Page 2 All Forward Group Corporation further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance. Product Specification & Technical Parameters Model PRO-INS24N1 PRO-INS30N1 PRO-INS36N1 Rated Voltage 110 ~120V ~120V ~120V...
-
Page 3: Recommendations And Suggestions
RECOMMENDATIONS AND SUGGESTIONS CAUTION TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURE TO PERSONS, PLEASE OBSERVE THE FOLLOWINGS: 1. Installation work and electric wiring (including switch location) must be done by the qualified person(s) in accordance with local applicable codes and standards, including fire-rated construction. -
Page 4: Installation And Use
CHARACTERISTICS INSERT Range Hood is designed for designer’s kitchen with the range hood hidden inside the cabinet, special molding design and metal or copper hood. No more visual machine hanging under the cabinet. Provide you a continue face of cabinets in your kitchen but at the same time have the range hood hidden and provide you with the benefit of extracting the oil and smoke from your cooking. -
Page 5: Mount Heights & Clearance
Note 1: On stainless steel hoods, carefully remove the plastic protective film from all exterior surfaces of the hood and chimney prior to final installation. Note 2: At least two people will be required to mount the hood. MOUNT HEIGHTS & CLEARANCE Minimum mount height between range top to hood bottom should be no less than 25”... -
Page 6: Duct Run Calculation
Ducting (not provided) NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use Metal duct work only. Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape. -
Page 7: Maintenance And Cleaning
NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch fire. The risk of self combustion is higher when the oil has been used several times. This Crown hood is equipped with five buttons control:- Light High... -
Page 8: Hood Cleaning
Remove and clean by hand in a basin of hot soapy water. The filter is also dishwasher safe. If heavily soiled, spray ‘Formula 409’ or equivalent degreasing detergent and leave to soak. Dry filters and re-install before using hood. Counter can be reset by continuous pressing the ‘+’ button after turning off the range hood. - Page 9 Preparing the range hood: 1. Open the electrical knockout which is best for your wiring. 2. Fix the shutter to the range hood’s vent; prevent the leakage of oil by taping the connection with aluminum metal adhesive tape, or duct tape. 3.
- Page 10 4. Reinstall the range hood’s bottom cover and stainless steel baffle filters. 5. Reinstall the oil container. 6. Turn on the power and check the operation of the fans and light. Dismantling, Cleaning and Re-assembly NOTE 1. Whenever dismantling, re-installing or maintaining the range hood, always make sure that the power ir off.
- Page 11 Cleaning Put all the dismantled parts in water with neutral detergent to 30 minutes, and then wash with a nylon brush. Make sure that all parts are dry before reinstallation. Note: Dismantled parts are: oil container, base plate, vane and van cap, and stainless steel baffle filters.
-
Page 12: Troubleshooting
Trouble shooting CAUTION: Disconnect the power supply before servicing. Cause and Method of Repairing Tools required Status Check circuit breakers Philips If the power supply is damaged, No power Screwdriver please call for a qualified person a).The motor is broken, replace motor. The motor Philips b).