Page 1
USER MANUAL Model: CPE-609 Tips: Thank you for ordering and using ULNA CPE609 Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time. The installation of this device requires some network knowledge. If you can't install it, please let us know or contact a professional.
1. Overview 1.1 Introduce ULNA CPE609 is a long-distance 5.8G wireless transmission device. It uses wireless communication technology to transmit network data using air as a medium to perform long-distance point-to-point or point-to-multipoint interconnection. The working data link layer realizes the interconnection of local area networks.
USER MANUAL Model: CPE-609 Tips: Thank you for ordering and using ULNA CPE609 Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time. The installation of this device requires some network knowledge. If you can't install it, please let us know or contact a professional.
3.1. Button Operation Reset Button: Press and hold for 10S to reset the wireless bridge; in setup mode, short press once to toggle a different character to pairing. A-B Button: Pushing the button to "A" indicates that the bridge acts as the master bridge (transmitter), and pushing the button to "B"...
Digital Tube Display that a fixed number is solid, it means that the two bridges are paired successfully and are working. Point Light A, B status lights, lighting is B mode, no lighting is A mode. 5. Quick Start 5.1 PoE Power Supply The CPE609 wireless bridge adopts a PoE power supply, which is easy to install and manage while saving costs.
7. Finally connect other devices(Router, PC, Switch) and install them to the target location. (TIPS:Steps 1, 4 and 5 are already pre-set) 5.3 Point to Multipoint Pairing Step: e.g. 1 master bridge with 3 slave bridges 1. Switch one unit to A(Master Bridge) and 3 units to B(Slave Bridge); 2.
1. Choose to pole mount or wall-mounted, adjust the CPE orientation, the bracket is not included in the package. Recommended ULNA Universal Bracket (ASIN: B0B5TWYHWC). 2. Please, prepare a long enough network cable to connect the PoE adapter and CPE, the network cable is connected to the LAN port of the CPE, and the other end is connected to the PoE port of the PoE adapter.
8.2 Case 2: Point-to-point extended of surveillance cameras range 8.3 Case 3: Point-to-multiple point extended surveillance cameras range 8.4 Case 4: Point-to-point extended surveillance cameras range support01@ulnastore.com...
9. Advanced Settings Note: You can work the wireless bridge without advanced settings 1. Computer Access Wireless Bridge, connect the CPE to the computer Refer to the figure left to connect the CPE to the computer through a PoE adapter and an Ethernet cable. 2.
Page 13
3. Change your computer's IP address to 192.168.255.xxx (192.168.255.xxx cannot be the same as the IP of the CPE), then the entry IP address is 192.168.255.xxx, the subnet mask is 255.255.255.0(Autofill), the Default gateway is 192.168.255.xxx, Preferred DDS server 192.168.255.xxx. You can use 192.168.255.105(xxx=2) in the reference picture to set.
Page 14
6. In the wireless settings, turn off "Hide SSID", then modify the SSID name and WiFi password, and finally click "Apply" to complete the setting. Digital & IP & WiFi Correspondence Chart You can check the SSID and password through this chart. support01@ulnastore.com...
11. Technical Support and Service A. Thank you for your order and for using ULNA Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time; B. The installation of this device requires some network knowledge. If you can't install it, please let us know or contact a professional.