Sharp ZQ-4400 Service Manual page 5

ZQ-4400
ZQ~4450
Notes:
* To interrupt data Gancise press s [ON].
© {ta connector is disconnected, or a similar problem occurs during
data. transfer, the message "I/O DEVICE-ERROR" vl appear.
Press [G:CE] [C-CE] to clear the error.
* After data transfer, the data on the trasrhitter 18 preserved.
® There may be a voltage level difference between the connected
Organizers which: may cause the display contrasts to change.
Should this occur, wade! the contrast as required.
ianetering data between ZQ-4450
Organizers
Data in the SCHEDULE, ANNIVERSARY, TEL, MEMO, TO DO and
EXPENSE modes can be transferred. The data is transferred and
verified by mode (all entries in a mode or a directory - TEL 1, TEL 2,
TEL 3) of by efitry. In addition, data can be backed up.
Transferring data by mode or by entry
During mode transfer, data previously stored in the specified mode of
the receiver are deleted. Proceed with caution.
Note: When mode transfer is carried out in the TEL mode, all listings
in the specified directory will be transferred. (In this case, the
directory file name is transferred at the same time.)
1. Select the mode on the transmitter and receiver.
SCHEDULE (Transmitter)
SCHEDULE] (Receiver)
2. Select the data transfer function on the receiver.
OPTION
3. Select " J RECEIVE" to set the unit in the receive mode.
2 . <UNIT TO UNIT>
RECEIVING
MODE
4. Select the data transfer function on the transmitter.
[2nd] [OPTION]
Note: To transfer a single ae display the desired entry and
press [2nd] [OPTION].
5. Select" J SEND" to transfer data.
1
Notes:
° 'Af the mode of the transmitter and the mode of the receiver are not
the same, data transfer is not established. The message "DATA
" ERROR" is displayed. -
When transferring TEL data, directories on the transmitter and
receiver can be different. The contents received by the receiver will
be stored in'thié open directory, For example, if TEL 1 is selected
on the transmitter and TEL*3.0n the receiver before the data
transfer is established, the contents of TEL 1 will be sent to and
stored in TEL3.. 4 '
© Turn off the SECRET function on "bath the irananiliiee and the
Transferring backup data re.
All the contents of the Organizer are transferred. During backup data
transfer, data stored on the receiver are deleted. Proceed with cau-
tion. (Backup data transfer is only possible between identical
products.)
1. Select the data transfer function on the receiver and.set it in the
receive mode for backup data transfer.
<UNIT TO UNIT>
2
BACKUP
RECEIVING
MODE
2. Select the data transfer function on the transmitter and perform
backup data transfer.
1
Verifying data
It is possible to verify data by mode or by entry. If any discrepancies
are found, the message "VERIFY ERROR* is displayed.
Verify data in the SCHEDULE mode.
1. Select the mode on the transmitter and the receiver.
SCHEDULE (Transmitter)
SCHEDULE] (Receiver)
2. Set the receiver in the verify mode.
[2nd] [OPTION] 3
<UNIT TO UNIT>
—-VERIFYING-
3. Select the data transfer function on the transmitter.
Note: To verify an entry, display the entry to be verified and
press | 2nd| {| OPTION]. ;
4. Perform verification.
1
Transferring data with another ZQ series
or IQ series Organizer
Data transfer restrictions
There are some restrictions when transferring data with any ZQ
series Organizer other than the ZQ-4450 or the IQ series Organizers
(previously shown). These restrictions result from differences in func-
tions and the maximum allowable size of an entry between the Or-
ganizers.
When transferring SCHEDULE data from ZQ 6000 .
series, 1Q-8000, 1Q-7000 or ZG-5000 series .
Organizers
® Any alarms set on SCHEDULE data 'ianslented 'froth the z
000,
receiver before mode transfer.
* if the amount of memory availablé on the receiver at the time of
transfer is insufficient, data transfer is not possible. The message
"MEMORY FULL" appears. Delete any unnecessary data, verify
whether the available memory is sufficient, and repeat the data
transfer procedure.
* |fan error message appears while transferring data, press
to clear the error.
their precise setting time for specific event, will be set to the
event's Te time on thé ZQ- ee