Advertisement
安装步骤
如何安装水龙头
首先，将O型圈(1)嵌入水龙头本体(2)
底部的槽中。将软管及牙管(3)装入洗
涤盆的安装孔中。使龙头本体的底部
接触台面。
2
将两个螺钉(4)旋入固定环(5)。从洗涤
盆下方依次把垫片(6)、金属垫片(7)及
1
装有两个螺钉的固定环装到牙管上。
调整水龙头的位置，使得软管(8)朝正
前方，两进水软管(9)在左右对称的位
置。锁紧两螺钉，将龙头固定在洗涤
盆上。
4
把进水软管接到水源上，当面对龙头
时，左边接冷水源，右边接热水源。
将重锤(10)和塑料夹(12)装到软管组件
(11)上，调整位置使其距龙头底面距离
合适。将软管组件(11)装入软管(8)内 。
如何使用花洒
打开手柄，手持使用花洒时，取下花
洒，并拉出软管。
按下图中(A)处，可关闭水流。按下图
中(B)、(C)处，可分别得到两种水流，
如图(a)、(b)所示。
注意：不要用力过猛或拉出过长，以
免造成软管及接头损坏。
a
1230969-T2-F
INSTALLATION
How to Install the Faucet
Slide the o-ring(1) into the groove of the
body(2). Put the hoses and shank(3) into
the mounting hole of the sink. Let the
bottom of the body against the deck.
Screw two screws(4) into the threaded
ring(5). From underside of the sink, place
the washer(6), the metal washer(7) and
3
threaded ring with two screws onto the
shank. Position the faucet so that the
hose(8) is toward the front and two
6
hoses(9) are symmetrical. Tighten two
7
screws to secure faucet to sink.
5
Attach the hoses to water supplies.
When facing the front of the faucet, the
8
left hose is cold water, the right is hot
water.
11
Put the weight(10) and clip(12) onto the
hose assembly(11). Adjust the weight so
12
that the distance is right from the bottom
10
of the faucet to the weight. Insert the
9
hose assembly(11) into the hose(8).
How to Use the Spray
Open the handle, if you want to use the
B
C
spray by hand, take the spray and pull
out the hose.
A
Press the button(A) as shown for the
water close. Press the button(B), (C) as
shown for two different forms of water
flow, as figure(a), (b) shown.
NOTE: Please pull it gently and do not
draw out the spray hose too long, or you
b
may damage the hose and connector.
安装结果检查
检查并确保所有衔接处都已拧紧，确
保手柄在关闭位置。打开主水源和排
水系统，检查并修理有漏水的接口。
将起泡器(14)和花洒(13)拆下，让水流
约一分钟以清除杂质。冲洗花洒的滤
网垫片及起泡器。关闭水龙头，重新
装回起泡器和花洒。
使用说明
将手柄轻轻提起，顺时针旋转为冷水，逆时针旋转
为热水。
清洗说明
适用于所有加工处理过的表面：以中性肥皂水清洗镀
层表面，再以干净的软布彻底擦干整个表面，许多清
洁剂，比如氨水、去污粉及洁厕灵等，会对电镀表面
造成伤害，切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌的
水龙头及其配件上。
龙头本体背面标有"LEAD FREE"字样，即产品符
合美国AB1953法令的要求。
2
1230969-T2-F
INSTALLATION CHECKOUT
13
Ensure that all coupling nuts are tight.
。
Ensure that the lever handle is in the off
position. Turn on the main water supply
and drain, and check for leaks. Repair as
needed.
14
Remove the aerator(14) and spray(13).
Run hot and cold water about one
minute to remove any debris. Remove
any debris from the aerator and filter
washer of the spray. Shut off the faucet.
Reinstall the aerator and spray.
HANDLE OPERATION
Lift the handle gently. Turn clockwise for cold water,
counter-clockwise for hot water.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm
water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals, such
as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended
for cleaning.
Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.
"LEAD FREE" is marked on the back of the faucet
signifying its compliance with the United States
AB1953．
3
Advertisement
