Advertisement

Quick Links

ZYX
User Manual
V1.00
2016.01.18 Revision
@2016 TAROT All Rights Reserved.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZYX T-3DIII and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Tarot ZYX T-3DIII

  • Page 1 User Manual V1.00 2016.01.18 Revision @2016 TAROT All Rights Reserved.
  • Page 2: Table Of Contents

    3. Basic Setup ............................ 11 4. Channels ............................12 5. Tools............................... 13 6. Firmware Update ........................... 13 VI. Troubleshooting ........................... 15 VII. Specifications ............................. 16 VIII. Port Descriptions ..........................17 IX. LED Indicators ..........................18 @2016 TAROT All Rights Reserved.
  • Page 3: Warning And Disclaimer

    Keep the entire components far from children and flammable & combustible materials! Because we have no control of the use, mounting, assembly and modification processes, TAROT will not assume any legal responsibility for the injury or damage.
  • Page 4: Product Introduction

    Pan Follow (PF) mode and First Person View (FPV) mode. Moreover, video out and battery charging of GoPro Hero 3/3+/4 can be achieved through ZYX T-3D III. @2016 TAROT All Rights Reserved.
  • Page 5: Product List

    First Person View (FPV) mode. Gimbal Main Controller Module*1 Main Components Pack 5V OUT & Receiver & AV Cable*1 Gimbal Main Controller & Gimbal Connection Cable*1 USB Module*1 Connection Cable to Flight Controller*1 GoPro Charging & AV-OUT Cable*1 @2016 TAROT All Rights Reserved.
  • Page 6: Mounting & Configuration

    3、 If you have 5V power supply to the receiver, please disconnect the 5V power of CH1/SBUS channel. Video Connect the video wireless transmission module to AV out port. DO NOT misconnect signal and video cable. Flight Controller Gimbal can work independently without Tarot ZYX-M Flight Control Module, but its @2016 TAROT All Rights Reserved.
  • Page 7: Gimbal Working Mode

    For instance, angle offset might occur when the accelerated state lasts for a long time. If you are pursuing a perfect performance, please connect the gimbal and Tarot ZYX-M Flight Control Module to the DATA/FC channel of gimbal controller through the special cable in main components pack.
  • Page 8 TAROT Take the three-positioned switch as an example: Position 1 refers to FPV Mode; Position 3 corresponds to AL Mode.Position 1 and Position 3 can be exchanged. @2016 TAROT All Rights Reserved.
  • Page 9: Flight Test

    Initialization will last for a relatively long time if the sensor deviation or drifts are large. 3. After sensor initialization process finishes, gimbal angles corresponds to INIT ANGLE in the assistant software. @2016 TAROT All Rights Reserved.
  • Page 10: Zyx T-3D Iii Assistant Software

    When finish parameters setup, you should click "Write Flash" to ensure all the parameters have written to the gimbal. Moreover, the gimbal will automatically run the parameters you have saved in the flash next time. @2016 TAROT All Rights Reserved.
  • Page 11: Basic Setup

    Please press “ENTER” button after modifying Please press “ENTER” button after modifying the Attention: it has been adjusted to an appropriate value the parameters. parameters. before leaving factory. If vibrations do not occur, please do not modify this value. @2016 TAROT All Rights Reserved.
  • Page 12: Channels

    Rate Mode:The position of the stick is corresponding to the rotate speed of the gimbal. Angle Mode:The position of the stick is corresponding to the angle of the gimbal. @2016 TAROT All Rights Reserved.
  • Page 13: Tools

    Methods to calibrate It is necessary to keep the gimbal in the stationary state. Click "Calibrate Sensors". When "Calibration is successful" shows on status bar, the calibration procedures finishes. 6. Firmware Update Update Procedures: @2016 TAROT All Rights Reserved.
  • Page 14 You can repeat upgrading for several times until your device is broken. Moreover, you could screenshot the upgrade procedures and send your concerns or problems through the feedback on the top right corner of the assistant software. @2016 TAROT All Rights Reserved.
  • Page 15: Troubleshooting

    1. Check and fix the wiring cables; quickly. controller and its main body becomes 2. Make sure whether or not there is resistance to loose. gimbal rotation. Then, power cycle the gimbal. 2. Gimbal stall protection goes far beyond ten times. @2016 TAROT All Rights Reserved.
  • Page 16: Specifications

    PAN: ± 200 deg/s Controllable Rotation Range TILT: -120 deg ~ +15 deg PAN: -125 deg ~ +125 deg Attitude Control Accuracy ± 0.02° Supported Camera GOPRO HERO 3/3+/4 Windows XP/VISTA/7/8 Assistant Software Supporting Platform @2016 TAROT All Rights Reserved.
  • Page 17: Port Descriptions

    Gimbal Main Controller Assistant Software Update & Gimbal Data Input Port 5V/RC/AV 5V Power Output & Receiver Input & AV-OUT Port Motor Drive & Sensor Module Port Debug Port. Do not connect any external device. DEBUG @2016 TAROT All Rights Reserved.
  • Page 18: Led Indicators

    2. Gimbal stall protection goes far beyond ten times. Motor Drive & Sensor Module Indicators Status BLUE light blinks once. POST (Power On Self-Test) Status. BLUE light is constantly on. POST (Power On Self-Test) fails. @2016 TAROT All Rights Reserved.

Table of Contents