Related Manuals for CR-Tec ER PREMIER ER20
Summary of Contents for CR-Tec ER PREMIER ER20
- Page 1 ER PREMIER Electric Actuators Installation and Operation Manual 20Nm IP65 Enclosure protection Duty cycle...
-
Page 2: Table Of Contents
This product meets the European Directive 2012/19/UE about electrical and electronic equipment (DEEE). It mustn't be mixed with common waste. Please, recycle or dispose of them according to your country laws. CR-TEC Engineering Inc. • info@crtec.com • www.crtec.com • 203-318-9500... - Page 3 Do not mount the actuator less than 30 cm of a electromagnetic disturbances source. Do not position the equipment so that it is difficult to operate the disconnecting device. CR-TEC Engineering Inc. • info@crtec.com • www.crtec.com • 203-318-9500...
-
Page 4: Position Indicator
1. Turn the knob to position MAN (counter-clockwise) and hold it in position. 2. Turn the outgoing drive shaft of the actuator with the help of an adjusting spanner. 3. In order to re-engage the reduction, release the knob (spring return). CR-TEC Engineering Inc. • info@crtec.com • www.crtec.com • 203-318-9500... -
Page 5: Dimensions
F03/F05-F04 plate Star 14 (mm) Square / Star (mm) Depth (mm) ER35/60/100 Star 22 (mm) ISO F flange Diameter (mm) M threaded Depth (mm) Screws quantity 14.2 14.2 14.2 / 16.4 16.4 CR-TEC Engineering Inc. • info@crtec.com • www.crtec.com • 203-318-9500... -
Page 6: Electric Wiring
To adjust the position of the auxiliary contacts, make rotate the two superior cams by using the appropriate wrench. Re-mount the cover, fasten the four screws and attach the position indicator. CR-TEC Engineering Inc. • info@crtec.com • www.crtec.com • 203-318-9500... - Page 7 Lead Wire. If you are using the Lead Wire type, a jacketed multi-conductor wire is recommended. A rubber grommet is compressed around the jacketed conductor to make a seal. If a tight seal is not important, then any type of wiring can be used. CR-TEC Engineering Inc. • info@crtec.com • www.crtec.com • 203-318-9500...
- Page 8 Open Open Close IF WIRING TROUGH THE CABLE GLAND FC1 OPEN SWITCH (N/O) FC2 COMMON FC! COMMON FC2 CLOSE SWITCH (N/O) 24V 50/60Hz (24V DC) 100V-240V 50/60Hz (100V-350V DC) — SNAA690000 CR-TEC Engineering Inc. • info@crtec.com • www.crtec.com • 203-318-9500...
-
Page 9: Electronic Boards
=> check that the valve torque is not superior to the maximum torque stand by the actuator => check that the actuator do not exceed the duty cycle indicated (possible overheat) To re-start the actuator, reverse the sense of rotation or switch the power off and on. CR-TEC Engineering Inc. • info@crtec.com • www.crtec.com • 203-318-9500... -
Page 10: Technical Data
1 ISO M20 cable gland and 1 DIN43650 3P+T connector Circuit breaker type D, nominal current according the number of actuators (max. 4 actuators) or Inrush current use a inrush current limiter at the output of the circuit breaker. CR-TEC Engineering Inc. • info@crtec.com • www.crtec.com • 203-318-9500... - Page 11 CR-TEC Engineering Inc. CR-TEC Engineering Inc. 15 Orchard Park Road, Unit 18 Telephone 203-318-9500 • Fax 203-245-2575 Catalog DSBA3100 • Rev. 02/21/2022 info@crtec.com • www.crtec.com...
Need help?
Do you have a question about the ER PREMIER ER20 and is the answer not in the manual?
Questions and answers