Table of Contents
Advertisement
EN 34
5.
Q522.1E LB
5.8.5
Display option code
Caution: In case you have replaced the SSB, always check the
display option code in SAM, even if you have picture. With a
wrong display option code it is possible that you have picture,
but that in certain conditions you have unwanted side-effects.
5.8.6
Upgrade EDID NVM
To upgrade the EDID NVM you must short circuit pin 7 of the
EDID NVM to ground. Therefore some test points (EDID1,
EDID2 and EDID3) are foreseen next to the HDMI connectors
(figure "EDID-NVM pins"). See ComPair for further instructions.
EDID 3 EDID 2
Figure 5-13 EDID-NVM pins
Table 5-3 NAND flash content
NAND Flash content
Partition
JFFS2 partition 1 (application read write data)
JFFS2 partition 0 (Application read only once data)
JFFS2 partition 0 (Application read only upgradable data) wizard pictures, display file, cabinet file, upgrade assistant, ...
SQUASHFS partition
BFFS partition 2 (DVD OK)
BFFS partition 1 (DVD cursor down)
BFFS partition 0
Block 0
•
The above overview of the NAND Flash shows the content
of the different partitions. It also shows which part of the
one-zip file erases and programs which part of the NAND
Flash.
•
Remark: the above does not mean that you can reprogram
your HDMI keys with the "UpgradeAll.upg" file from the one
zip file. This can only be done in a secure environment (e.g.
the factory).
•
The "UpgradeAll.upg" file is only used in the factory.
•
The "FlashUtils.upg" file is only used by service centra
which are allowed to do component level repair on the
SSB.
Automatic Software Upgrade
In "normal" conditions, so when there is no major problem with
the TV, the main software and the default software upgrade
application can be upgraded with the "AUTORUN.UPG" (FUS
part of the one-zip file: e.g. 3104 337 03801 _FUS _Q582E_
0.37.0.0_commercial.zip). This can also be done by the
consumers themselves, but they will have to get their software
from the commercial Philips website or via the Software Update
Assistant in the user menu (see DFU). The "autorun.upg" file
must be placed in the root of your USB stick.
How to upgrade:
Service Modes, Error Codes, and Fault Finding
EDID 1
H_17650_089.eps
160108
Content
Channel table, EPG data,...
HDMI keys, back up display file, ...
Main software (Mips), Linux structure (root file system)
Default software upgrade application TriMedia software boot
batch file 2
Back up software upgrade application boot batch file 1
Linux kernel JETT : needed for ComPair
Jaguar Boot loader boot batch file 0
μBTM partition table
5.9
Software Upgrading
5.9.1
Introduction
The set software and security keys are stored in a NAND-
Flash, which is connected to the PNX85xx via the PCI bus.
It is possible for the user to upgrade the main software via the
USB port. This allows replacement of a software image in a
stand alone set, without the need of an E-JTAG debugger. A
description on how to upgrade the main software can be found
in the DFU.
Important: When the NAND-Flash must be replaced, a new
SSB must be ordered, due to the presence of the security
keys!!! (copy protection keys, MAC address, ...).
Perform the following actions after SSB replacement:
1. Set the correct option codes (see sticker inside the TV).
2. Update the TV software (see the DFU for instructions).
3. Perform the alignments as described in chapter 8 (section
"Reset of Repaired SSB").
4. Check in CSM if the HDMI keys are valid.
5.9.2
Main Software Upgrade
The software image resides in the NAND-Flash, and is
formatted in the following way (refer to figure "NAND-flash
content"):
One ZIP
Fuse UPG
Erase
Program Erase
X
X
X
X
X
X
1. Copy "AUTORUN.UPG" to the root of your USB stick.
2. Insert USB stick in the side I/O while the set is in ON
MODE. The set will restart and the upgrading will start
automatically. As soon as the programming is finished, you
will get the message that you can remove your USB stick
and restart the set.
Manual Software Upgrade
In case that the software upgrade application does not start
automatically, you can also start it manually.
How to start the software upgrade application manually:
1. Disconnect the TV from the Mains/AC Power.
2. Press the "OK" button on a Philips DVD RC-6 remote
control (it is also possible to use the TV remote in "DVD"
mode). Keep the "OK" button pressed while reconnecting
the TV to the Mains/AC Power.
3. The software upgrade application will start.
Attention!
In case that you have started the download application
manually, the "autorun.upg" will maybe not be recognized.
What to do in this case:
1. Create a directory "UPGRADES" on your USB stick.
Upgrade all UPG
Flash Utils UPG
Program Erase
Program
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Advertisement
Table of Contents
