Related Manuals for GreenWorks Pro GLPS80210
Summary of Contents for GreenWorks Pro GLPS80210
- Page 1 80V 10” BRUSHLESS POLESAW GLPS80210 Owner’s Manual TOLL-FREE HELPLINE: 1-855-345-3934 www.greenworkstools.com/80v-pro Read all safety rules and instructions carefully before operating this tool.
-
Page 2: Table Of Contents
CONTENTS Contents ..........................2 Product Specifications ......................2 Safety Rules ........................3 Symbols ..........................7 Know Your Polesaw ......................9 Assembly ........................... 10 Operation ..........................13 Battery & Charger Maintenance ..................19 Maintenance..........................21 Environmentally Safe Battery Disposal.................27 Troubleshooting........................28 Warranty..........................29 Exploded View ........................30 Part List ..........................31 PRODUCT SPECIFICATIONS 80V 10"... -
Page 3: Safety Rules
SAFETY RULES W A R N I N G Read and understand all instructions before using this product. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. WORK AREA SAFETY • Keep work area clean and well lit. Cluttered or dark areas invite accidents. • Do not operate polesaw in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. - Page 4 SAFETY RULES POLESAW USE AND CARE • Do not force the polesaw. Use the correct polesaw for your application. The correct polesaw will do the job better and safer at the rate for which it was designed. • Do not use the polesaw if the switch does not turn it on and off. Any polesaw that cannot be controlled with the switch is dangerous and must be repaired.
- Page 5 SAFETY RULES • To reduce the risk of electrocution, never use near any electrical power lines. Contact with or use near power lines may cause serious injury or electric shock resulting in death. • Always use two hands when operating the polesaw. • Always use head protection when operating the polesaw overhead.
- Page 6 SAFETY RULES W A R N I N G (PROPOSITION 65) Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: •...
-
Page 7: Symbols
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. DESIGNATION SYMBOLS EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second) - Page 8 SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
-
Page 9: Know Your Polesaw
KNOW YOUR POLESAW Read this operator's manual and safety rules before operating your polesaw. Compare the illustration in (Figure 1) to your polesaw in order to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Polesaw Extension Pole Scabbard... -
Page 10: Assembly
ASSEMBLY INSTRUCTION UNPACKING This product has been shipped completely assembled. • Carefully remove the product and any accessories from the box. Make sure that all items listed in the package contents section are included. • Inspect the product carefully to make sure no breakage or damage occurred during shipping. •... - Page 11 ASSEMBLY INSTRUCTION W A R N I N G If any parts are damaged or missing, do not operate this product until the parts are replaced. Using a product with damaged or missing parts could result in serious personal injury. W A R N I N G Do not attempt to modify this product or create accessories not recommended for use with this product.
- Page 12 ASSEMBLY INSTRUCTION W A R N I N G Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. W A R N I N G Always wear safety goggles or safety glasses with side shields when operating power tools.
-
Page 13: Operation
OPERATION Press Button Press Button Hole Lock Nut Step 2 Scrench Step 3 W A R N I N G Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. W A R N I N G Do not use any attachments or accessories not recommended by the manufacturer of this product. - Page 14 OPERATION ADDING BAR AND CHAIN LUBRICANT (See Figure 3) Use Bar and Chain Lubricant. It is designed for chains and chain oilers, and is formulated to perform over a wide temperature range with no dilution required. NOTE: Polesaw comes from the factory with no bar and chain oil added. Level should also be checked after every 30 minutes of use and refilled as needed.
- Page 15 OPERATION BATTERY PACK (See Figure 4) I M P O R T A N T The battery pack is not charged when it is purchased. Before using the polesaw for the first time, place the battery pack in the battery charger and charge it fully. Be sure to read all safety precautions, and follow the instructions in the section entitled Charging Procedure.
- Page 16 OPERATION I M P O R T A N T This Lithium-ion battery pack is equipped with an internal circuit breaker which will automatically shut off the power to the tool and then reset itself once cooled. Follow these steps if an overload occurs while under heavy use: 1.
- Page 17 OPERATION PREPARATION FOR CUTTING (See Figure 6-7) • Wear non-slip gloves for maximum grip and protection. • Maintain a proper grip on the unit whenever the motor is running. Use your right hand to firmly grip the rear handle while your left hand has a firm grip on the pole shaft. •...
- Page 18 OPERATION LIMBING AND PRUNING(See Figure 8) This unit is designed for trimming small branches and limbs up to 6 in. (15.2 cm) in diameter. For best results, observe the following precautions: • Plan the cut carefully. Be aware of the direction in which the branch will fall. •...
-
Page 19: Battery & Charger Maintenance
BATTERY & CHARGER MAINTENANCE CHARGING PROCEDURE (See Figure 9) NOTE : The battery is not shipped fully charged. It is recommended to fully charge before first use to ensure that maximum run time can be achieved. This lithium-ion battery will not develop a memory and may be charged at any time. A fully discharged battery pack will require approximately 90 minutes to fully charge from a discharged state. - Page 20 BATTERY & CHARGER MAINTENANCE W A R N I N G If the battery is inserted into the charger when warm or hot, the CHARGING LED indicator light on the charger may switch on and illuminate ORANGE. If this occurs allow the battery to cool outside of the charger from approximately 30 minutes.
-
Page 21: Maintenance
MAINTENANCE W A R N I N G When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. W A R N I N G Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. - Page 22 MAINTENANCE CHAIN TENSION • Stop the motor and remove the battery before setting the chain tension. Turn the bar cover knob counterclockwise to loosen the bar cover but do not remove the bar cover. Turn the chain tensioning screw clockwise to tension chain. Turn the guide bar knob clockwise to tighten. Refer to the Replacing the bar and chain section for additional information.
- Page 23 MAINTENANCE REPLACING THE BAR AND CHAIN • Remove the lock knob and chain cover. • The bar contains a bar stud slot that fits over the bar stud. The bar also contains a chain tensioning pin hole that fits over the chain tensioning pin. •...
- Page 24 MAINTENANCE CHAIN OILER • Use a lubricant that is designed for chains and chain oilers and is formulated to perform over a wide temperature range with no dilution required. • Remove the cap and carefully pour approximately 2 oz (57 g) of bar and chain lubricant into the bar lube reservoir.
- Page 25 MAINTENANCE CHAIN MAINTENANCE For smooth and fast cutting, the chain needs to be maintained properly. The following conditions indicate that the chain requires sharpening: • Wood chips are small and powdery. • Chain must be forced through the wood during cutting. •...
- Page 26 MAINTENANCE HOW TO SHARPEN THE CUTTERS Be careful to file all cutters to the specified angles and to the same length, as fast cutting can be obtained only when all cutters are uniform. • Tighten the chain tension enough that the chain does not wobble. Do all of your filing at the midpoint of the bar.
-
Page 27: Environmentally Safe Battery Disposal
ENVIRONMENTALLY SAFE BATTERY DISPOSAL The batteries used in this polesaw’s battery pack contain the following toxic and corrosive material: LITHIUM-ION, a toxic material. W A R N I N G Toxic materials must be disposed of in a specific manner in order to prevent contamination of the environment. -
Page 28: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Bar and chain Check chain tension for Tension chain. Refer to to the "Chain running hot and overtightened condition. Tensioning" section. smoking. Bar and Chain Oil Tank Low or Check the Oil Tank Level, and refill if Empty. -
Page 29: Warranty
3. Normal wear, except as noted below; 4. Routine maintenance items such as lubricants, blade sharpening; 5. Normal deterioration of the exterior finish due to use or exposure. GREENWORKS PRO HELPLINE: Warranty service is available by calling our toll-free helpline at 1-855-345-3934 . TRANSPORTATION CHARGES: Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. -
Page 30: Exploded View
EXPLODED VIEW... -
Page 31: Part List
PARTS LIST ITEM NO. PART NO. DESCRIPTION 311011726 Polesaw Handle Assembly 311021726 Pole Assembly 311021726 Pole Head Assembly 311051734B Oil Cap Assembly 311031726 Bar and Chain Assembly 33304590 Distance Sleeve 339001726 Sprocket 32209590 C-clip 311021009 Battery 311011010 Charger 34114155-1 Scabbard Greenworks Tools P.O.