Carrier WeatherMaster 50HC14 Installation Instructions Manual page 57

Do not mount the IAQ sensor in drafty areas such as near
supply ducts, open windows, fans, or over heat sources. Allow
at least 3 ft (0.9 m) between the sensor and any corner. Avoid
mounting the sensor where it is influenced by the supply air;
the sensor gives inaccurate readings if the supply air is blown
directly onto the sensor or if the supply air does not have a
chance to mix with the room air before it is drawn into the re-
turn airstream.
Wiring the Indoor Air Quality Sensor — For each sensor,
use two 2-conductor 18 AWG (American Wire Gage) twisted-
pair cables (unshielded) to connect the separate isolated 24 vac
power source to the sensor and to connect the sensor to the con-
trol board terminals.
To connect the sensor to the control, identify the positive (4
to 20 mA) and ground (SIG COM) terminals on the sensor. See
Fig. 66. Connect the 4-20 mA terminal to the RTU Open con-
troller at J4-2 and connect the SIG COM terminal to the RTU
Open controller at J4-3. See Fig. 83.
IAQ Sensor
SEN
COM
24 VAC
Fig. 83 — RTU Open Controller/Indoor CO
(33ZCSENCO2) Connections
OUTDOOR AIR QUALITY SENSOR (P/N 33ZCSENCO2
PLUS WEATHERPROOF ENCLOSURE) — The outdoor
air CO sensor is designed to monitor carbon dioxide (CO
2
levels in the outside ventilation air and interface with the venti-
lation damper in an HVAC system. The OAQ sensor is pack-
aged with an outdoor cover. See Fig. 68. The outdoor air CO
sensor must be located in the economizer outside air hood.
Wiring the Outdoor Air CO
supply is required for this sensor. A two-wire cable is required
to wire the dedicated power supply for the sensor. The two
wires should be connected to the power supply and terminals 1
and 2.
To connect the sensor to the control, identify the positive (4
to 20 mA) and ground (SIG COM) terminals on the OAQ sen-
sor. See Fig. 66. Connect the 4 to 20 mA terminal to the RTU
Open controller at J4 5. Connect the SIG COM terminal to the
-
RTU Open controller at J4 6. See Fig. 84.
-
OAQ Sensor/RH Sensor
SEN
COM
24 VAC
Fig. 84 — RTU Open Controller/Outdoor CO
Sensor (33ZCSENCO2) Connections
J4-2
J4-3
Sensor
2
Sensor A dedicated power
—
2
J4-5
J4-6
SPACE RELATIVE HUMIDITY SENSOR OR HUMIDI-
STAT
Humidi-MiZer
with the Humidi-MiZer option there are two pink (PNK) wires
loose in the control box used to control the dehumidification
function of the unit. These pink wires are meant to be tied to a
space humidistat or thermidistat on an electromechanical unit.
On RTU Open controller equipped units these pink wires must
be connected to J11
the dehumidification function for the unit. Disconnect the J11
Phoenix style connector from the board and use the plug
screws to secure the pink wires in pins 7 and 8, reconnect the
plug to the board at J11.
Relative Humidity Sensors (Space or Duct Mounted)
accessory space humidity sensor (33ZCSENSRH-01) or duct
humidity sensor (33ZCSENDRH-01) is used to measure the
relative humidity of air within the space or return air duct. The
RH reading is used to control the Humidi-MiZer option of the
rooftop unit. For wiring distances up to 500 ft (152 m), use a 3-
conductor, 18 or 20 AWG shielded cable. The shield must be
removed from the sensor end of the cable and grounded at the
unit end. The current loop power for sensor is provided by the
RTU Open controller as 24vdc. Refer to the instructions sup-
plied with the RH sensor for the electrical requirements and
terminal locations. RTU Open controller configurations must
be changed after adding an RH sensor. See Fig. 85 and 86 for
typical RH sensor wiring.
• J4 1 or J4
—
• J4 2 or J4
—
NOTE: The factory default for dehumidification control is nor-
mally open humidistat.
)
2
2
MOUNTING
HOLES
Fig. 85 — Space Relative Humidity Sensor Typical
2
57
® System Control Wiring
—
7 and 8 to allow the Open board to operate
-
4 = 24vdc loop power
—
5 = 4-20mA signal input
—
Io Vin Gnd Vo
SW2
Vin - J4-1 or J4-4 24Vdc
Io - J4-2 or J4-5 -20mA output
Wiring
In units equipped
The
—
WIRING
OPENING