Table of Contents
Advertisement
Setting the self-cleaning function
Press the menu button.
1.
The operating modes menu opens.
Use the rotary selector to select "Self cleaning".
2.
Touch the arrow
.
¿
3.
Cleaning setting 3 is suggested. You can start the
cleaning process immediately using the "Start/stop"
button or
select a different cleaning setting using the rotary
4.
selector.
Press the "Start/stop" button.
5.
Instructions for the cleaning operation appear on the
display.
Press the "Start/stop" button to start the cleaning
6.
operation.
Ventilate the kitchen when the cleaning function is
running.
The cooking compartment door locks shortly after
operation starts. The
H
mechanism appears on the right-hand side of the status
bar next to the elapsing duration.
The cooking compartment door cannot be opened until
the
symbol goes out in the status bar.
H
Once the cleaning has finished
An audible signal sounds. The oven stops heating. Use
the
button to switch off the audible signal. "Appliance
0
cooling down" appears on the display.
Cancelling the cleaning operation
Use the "On/off" button to switch off the oven. The
cooking compartment door cannot be opened until the
symbol goes out in the status bar.
H
Adjusting the cleaning setting
Once cleaning starts, the cleaning setting can no longer
be changed.
You can set the cleaning to run overnight
In the section "Time settings", you can find out how to
delay the end time. This allows you to use the oven at
any time throughout the day. ~ "Time-setting options"
on page 15
Once the cleaning function has ended
Once the cooking compartment has cooled down, use
a damp cloth to wipe off the ash that has been left
behind in the cooking compartment, on the accessories
and around the appliance door.
Remove the accessory supports and reattach the pull-
out rails.
Very bad soiling may cause white deposits to
Note:
remain on the enamel surfaces. This is residue from the
food and is harmless. It does not affect performance.
You can remove these residues using lemon juice if
required.
symbol for the locking
DCleaning
W ith good care and cleaning, your appliance will retain
C l e a n i n g
its appearance and remain fully functioning for a long
time to come. We will explain here how you should
correctly care for and clean your appliance.
Suitable cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Depending on the appliance
model, not all of the areas listed may be on/in your
appliance.
Caution!
Risk of surface damage
Do not use:
Harsh or abrasive cleaning agents,
■
Cleaning agents with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
High-pressure cleaners or steam cleaners,
■
Special cleaners for cleaning the appliance while it is
■
hot.
Wash new sponge cloths thoroughly before use.
Highly recommended cleaning and care products
Tip:
can be purchased through the after-sales service.
Observe the respective manufacturer's instructions.
:
Warning – Risk of burns!
The appliance becomes very hot. Never touch the
interior surfaces of the cooking compartment or the
heating elements. Always allow the appliance to cool
down. Keep children at a safe distance.
Area
Cleaning
Appliance exterior
Stainless steel
Hot soapy water:
front
Clean with a dish cloth and then dry with a soft
cloth.
Remove flecks of limescale, grease, starch and
albumin (e.g. egg white) immediately. Corrosion
can form under such flecks.
Special stainless steel cleaning products suitable
for hot surfaces are available from our after-sales
service or from specialist retailers. Apply a very
thin layer of the cleaning product with a soft cloth.
Plastic
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Do not use glass cleaner or a glass scraper.
Painted surfaces
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Control panel
Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Do not use glass cleaner or a glass scraper.
Cleaning
en
19
Advertisement
Table of Contents
