Table of Contents
Advertisement
FIELD OF APPLICATION
The Trisk Devilbiss IR6LT are designed to provide an
accelerated and even cure of most automotive refinishing
materials. Typically drying of putty, filler, base and top coats,
both water-based and solvent-based products. Its site of use is
the preparation area and finishing area. Within the automotive
industry and vehicle repair sectors, it is used to dry small areas
and cure materials before polishing .
PRODUCT DESCRIPTION
The easily maneuverable Trisk Devilbiss IR6LT are equipped
with both dual and single lamp cassettes for easy adjustment
and flexibility around curved parts without sacrifice to heat
distribution. The design, combined with a gas spring, makes
cassette adjustment simple. The IR lamps and reflectors are
protected against mechanical damage with a mesh. The
control unit enables flash off (50% power) and full bake
(100% power). The time can be set individually for each mode
(0-30 min). Additionally, the IR6LT unit is equipped with a
contactless temperature control where the temperature can be
set between 20°C and 99°C.
PARTICULAR ADVANTAGES
Unique reflector design
The Trisk Devilbiss IR6LT features a unique dimpled sheet
reflector that generates extremely even curing intensity and
temperature over entire surfaces. This ensures the fastest
possible curing time, while minimizing risk of over-curing or
burning sections of your coating.
Good maneuverability
The Trisk Devilbiss IR6LT are sized to cure higher surfaces such
as hood and roof. Lockable gas piston makes it very easy to set
point of parallel arm. IR6LT has a laser guided pyrometer
displaying surface temperature readout which make it even
easier to properly position the lamps.
TECHNICAL DATA
Electrical diagram, see page 9.
Rated Voltage
Rated power
Heating elements
Fuse*
Noice level
Max ambient temperature
during operation
Max ambient temperature
during storage and
transportation
* The dryer must be supplied by recommended fuse.
SB-81-016-R1 (11/2023)
TRU CURE IR6LT – GENERAL INFORMATION
380 V - 420 V
220 V - 240 V
50/60Hz
50/60Hz
3 Phase
Single Phase
6 emitters
6 emitters
Full power 6200W
Full power 6200W
6 quartz
6 quartz
Tungsten filament
Tungsten filament
Infrared emitters
Infrared emitters
16 A
30 A
Less than 70 dB
Less than 70 dB
(A)
(A)
40
C
40
C
o
o
70
C
70
C
o
o
INSTRUCTION TO THE OWNER
The owner of the mobile dryer must produce clear operating
instructions, adapted to local site conditions and applicable
national / regional requirements, and make these available to
all users.
Mobile dryer users must adhere to these operating instructions.
The mobile dryer user must always ensure that sufficient
technical ventilation is complied in accordance with the
applicable national / regional requirements.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the
appliance.
Dispose of spent items at the nearest environmental protection
facility for recycling.
WARNINGS
!
FIRE AND EXPLOSION
Do not use in an area until it is checked and cleared
of combustible and/or flammable materials.
Do not use in an area where the air may contain
flammable dust, gas, or liquid vapors.
Never direct the heating equipment towards any
pressurized vessel.
Never direct the heating equipment towards
combustible or flammable materials.
If you have a distance less than 60 cm/2 feet to the
object the temperature might raise quickly and the
risk for fire increases.
ELECTRICAL EQUIPMENT
The mobile dryer is operated by highly dangerous
electrical voltage.
ACCESSING ELECTRICAL EQUIPMENT
Before accessing live parts, remove the main
connector from the wall socket. Only professional
electricians may have direct access into the electrical
equipment.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
WARNING!
Intensive heat radiation. Hands, face and other parts
of the body should be exposed as little as possible to
the heat radiation.
5 / 12
EN
www.carlisleft.com
Advertisement
Table of Contents
