Download Print this page

Sealey SM28.V2 Manual page 2

50l mobile parts cleaning tank

Advertisement

Avoid unintentional starting. Ensure the switch is in the off position before plugging into mains supply.
9
DO NOT overfill tank or allow fluid level to fall below pump inlet.
8
DO NOT use the tank for a task it is not designed to perform.
8
DO NOT operate the tank if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT allow untrained persons to operate the tank.
8
DO NOT operate the tank when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT leave the tank operating unattended.
8
When not in use switch off the tank, close the lid and remove the plug from the power supply.
9
Dispose of waste liquids in accordance with local authority regulations.
9
WARNING! Protect the environment - DO NOT allow uncontrolled discharge of pollutants.
Keep the tank clean for best and safest performance.
9
2. INTRODUCTION
Heavy-duty one-piece tank. Fully sealed electric motor with magnetic drive pump unit. Lid features self-latching fusible link which automatically
snaps lid shut in the event of a fire. Includes removable shelf and small parts basket. Flexible metal nozzle directs solvent over work. Supplied
with workshop stand with integral storage shelf.
3. SPECIFICATION
Model no ................................................................. SM28.V2
Maximum Working Capacity: ............................................ 50L
Minimum working Capacity: ............................................. 40L
Overall Dimensions (W x D x H): .............775 x 540 x 960mm
Pump Output/hr: ............................................................. 200L
Supply: ...........................................................................230V
Tank Dimensions (W x D x H): ................775 x 540 x 265mm
4. ASSEMBLY
fig.1
4.1.
Refer to attached Parts Diagram.
4.2.
Remove parts from packing and take items out of the tank. Before assembly check parts to ensure they are complete and not damaged.
4.3.
Close lid of tank, gently and turn unit upside down. Rest tank on a clean soft surface (i.e. cardboard) ensuring lid is secured in the closed
position.
4.4.
Attach each of the 4 tank legs (13) with 4 sets each of 6mm screws, lockwashers and nuts (14,8,9) to the brackets on the tank (7) unit.
4.5.
Attach shelf (12) to holes located mid-way of 4 legs with 2 sets each of 6mm screws, lockwashers and nuts (14,8,9).
4.6.
Fit swivel castors, (37, 38) using nut and washer (40, 39).
4.7.
Return the tank unit to the upright position on its legs and open the spring tensioned tank cover (1).
4.8.
Thread the fitting of the flexible metal pipe (24) fluid outlet tube onto the pump elbow (13), fig.1. Place the pump housing lid (29) over the
open pump housing (20) with fluid intake perforations and raised ribs downward and over pump fig.2. Snap into place.
4.9.
Route the power cord of the pump housing assembly through the rectangular opening on the side of the tank unit (7) with the inlet filter
(28) downward and facing inward, fig's.3 & 4.
4.10.
The power switch is visible through the rectangular opening. Hook the raised offset tab on the rear of the pump housing (20) over the
bottom edge of the rectangular opening fig.4.
4.11.
Check to see that the tank plug (11) plug is tightly installed.
4.12.
Place the work shelf (6) over the edges on the walls of the tank (7).
4.13.
Make sure the nozzle of the flexible pipe (24) is facing in toward the centre of the tank (7) and downward.
4.14.
Installation of a flow-through parts cleaning brush and hose extension is optional.
4.15.
Fill unit with suitable, water-based degreasing solution sufficiently to cover the entire inlet filter (28) (approx.12 gallons).
Important Note: Follow degreasing solution mixing, usage and safety label instructions carefully before using.
4.16.
Plug power lead into mains supply.
4.17.
Turn Power Switch to the "On" position.
5. OPERATION
WARNING! Wear safety clothing, eye protection and gloves and ensure you read, understand and apply the safety instructions
in Section 1.
5.1.
Ensure the unit is located on a firm level surface in a well ventilated area and is switched off and unplugged from the mains power supply.
5.2.
Fill the tank with Sealey solvent - approx. 50 litres. Minimum level must cover pump inlet - approx. 40 litres. Follow the solvent
instructions on the packaging.
© Jack Sealey Limited
N
fig.2
Original Language Version
fig.3
SM28.V2 Issue:1
fig.4
21/06/22

Advertisement

loading