Download Print this page
Sealey SM233 Instructions
Sealey SM233 Instructions

Sealey SM233 Instructions

Air operated water based spray gun cleaning tank

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
! WARNING! Ensure Health & Safety, local authority, general
workshop practice regulations are adhered to when using
equipment.
! WARNING! Installation site must be equipped with suitable
fire extinguishers (water must not be used) and escape routes.
! WARNING! Disconnect the air supply from the tank before
changing accessories, servicing or performing any maintenance.
Maintain the tank in good condition (use an authorised service agent).
"
Replace or repair damaged parts. Use genuine parts only.
"
Unauthorised parts may be dangerous and will invalidate the warranty.
Locate the tank in a suitable working area. Ensure the tank
"
stands on a firm level surface. Keep area clean and tidy and free
from unrelated materials. Ensure the area is well ventilated and
has adequate lighting.
! WARNING! Ensure correct air pressure is maintained and not
exceeded. Recommended pressure (40 - 60psi).
Keep air hose away from heat, oil and sharp edges. Check air
"
hose for wear before each use, and ensure that all connections
are secure.
! WARNING! This tank is for use only with solvents for water
based paints.
Use only recommended solvents as a cleaning agent, do not pour
"
any other type of cleaning fluid into the tank.
Keep the tank clean. Remove and clean the suction filter regularly
"
for best performance.
! WARNING! DO NOT SMOKE and keep sources of ignition,
such as heaters, lamps, etc. away from the unit, together with
flammable or combustible materials, as there is an explosion risk.
! WARNING! Wear approved safety eye protection, mask and
gloves. If solvent gets on skin or in eyes wash thoroughly
with water and take any other action as required by the
solvent instructions.
Remove ill fitting clothing, ties, watches, rings and other loose
"
jewellery, contain long hair, and wear appropriate protective clothing.
Maintain correct balance and footing. Ensure the floor is not
"
slippery and wear non-slip shoes.
Keep non-essential persons away from the working area.
"
In case of fire in tank, do not attempt to move the unit or remove
"
spray guns.
DO NOT use the tank with the lid open and DO NOT use it for
#
spray gun testing.
DO NOT use the tank for any purpose other than for which it is
#
designed.
DO NOT operate the tank if any parts are missing or damaged as
#
this may cause failure and/or possible personal injury.
DO NOT over-fill the tank (max capacity 19 litres).
#
DO NOT direct air from the air hose at yourself or others.
#
DO NOT operate the tank when you are tired or under the
#
influence of alcohol, drugs or intoxicating medication.
When cleaning is complete, ensure all control valves are in the
"
'off' position and that the air supply is turned off.
! WARNING! It is operator's responsibility to ensure that there
is no uncontrolled discharge of any fluids used with this unit
and that appropriate arrangements have been made for correct
disposal of waste in accordance with government/local authority
regulations.
! WARNING! Do run the washer without the screen platform.
2. INTRODUCTION & SPECIFICATION
Fully enclosed, corrosion resistant tank suitable for containing
water and detergent necessary for cleaning spray guns using
water-based paint. Powerful and reliable diaphragm pump system
washes up to two guns simultaneously. Semi automatic operation.
INSTRUCTIONS FOR:
BASED SPRAY GUN CLEANING TANK
SPECIFICATION:
Operating pressure . . . . . . . . . . . . . . . . . . . . . . . . . .40-60 psi
Air consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4 cfm
Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75db
Interior tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Polythene
Cleans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 pots + 2 guns
Water capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19ltr
Width x depth x height . . . . . . . . . . . . . . .470 x 650 x 1000mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33.5kg
3. ASSEMBLY
Refer to fig.4.
3.1. Attach legs to the cabinet with the screws, washers and nuts
provided . Fit drain valve to base of tank.
4.
AIR SUPPLY
NOTE: The air supply for the SM233 must be equipped with a
regulator, filter/separator and oiler in order to ensure safe
operation and to prolong the life of the product. These items are
not supplied and must be purchased separately.
Consult your local Sealey dealer for a suitable product.
For recommended hook-up, see diagram below.
4.1. Ensure that the pump air valve and air inlet ball valve are closed
before connecting the air supply. See fig.3.
4.2. An air pressure of 40-60psi, and an available air volume of
2 - 4cfm will be required to operate the unit.
! WARNING! Ensure air supply is clean and does not exceed
60psi. Too high an air pressure and/or unclean air will
shorten the product life due to excessive wear, and may be
dangerous, causing possible damage and personal injury.
4.3. Drain the air supply tank daily. Water in the air line will damage
the unit.
4.4. Clean the air supply filter weekly.
4.5. Line pressure should be increased to compensate for unusually
long air hoses (over 8 metres). The minimum hose internal
diameter should be 10mm and fittings must have the same
internal dimension.
4.6. Keep hose away from heat, oil and sharp edges. Check hoses for
wear, and make certain that all connections are secure.
4.7. The air inlet connection is 1/4"NPT.
HOOK-UP
5. OPERATING INSTRUCTIONS
WARNING! Ensure you follow the safety instructions.
!
Wear approved safety gloves, goggles, mask, and
suitable clothing.
AIR OPERATED WATER
SM233
MODEL NO:
SM233 - 1 - 210607

Advertisement

loading

Summary of Contents for Sealey SM233

  • Page 1 SM233 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
  • Page 2 The construction file for this product is held by the Manufacturer and may be 98/37/EC Machinery Directive inspected, by a national authority, upon request by contacting Jack Sealey Ltd. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.