Table of Contents
Advertisement
Prior to Operation
1. Make sure your battery pack is (fully) charged.
2. Insert the appropriate drive accessory.
3. Select forward or reverse rotation.
4. Set the appropriate driving depth.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the rear grip. Take
care to not block the air vents
Switching On and Off (Fig. A)
1. To run the tool, press the variable speed switch
pressure exerted on the variable speed switch determines
the tool speed.
2. To stop the tool, release the variable speed switch
Lock on Button
7
To lock the trigger switch
operation, depress the trigger switch and push up the lock
9
on button
. The tool will continue to run. To turn the
tool off, from a locked on condition, squeeze and release
the trigger once. You will hear and see the lock on switch
return downwards.
CAUTION: Before using the tool (each time) be sure
that the locking button release mechanism is working
freely. Be sure to release the locking mechanism before
disconnecting the battery. Failure to do so will cause
the tool to start immediately the next time the battery is
inserted. Damage or injury could result.
Screwdriving (Fig. A, D)
For best results, hold the screwdriver with your hand directly in
line with the fastener and press the variable speed switch with
the last one or two fingers of the hand. This reduces the chance
of the screw slipping from the drive accessory when pressure
is applied.
To drive the fastener, place it on the bit, press the variable speed
switch and push the fastener into the workpiece with a smooth,
continuous motion. When the fastener is seated, the clutch will
disengage automatically.
23
.
7
. The
7
in the on position for continuous
1. Install bit tip in bit holder.
2. Adjust depth locator
3. Check for correct rotation, start screwdriver and place screw
on bit.
4. Contact work surface, applying forward pressure to drive
screw until depth locator contacts the work surface.
Screwgun will ratchet automatically, disengaging bit
from screw.
5. This depth sensitive screwdriver is suitable for driving
drywall screws.
For This Depth Sensitive Clutch Please Remember
•
The bit will not turn until pressure is applied to the unit.
Push to engage.
•
Trigger switch will not depress unless tool is in either
forward or reverse position.
Screwdriving with Collated Screws (Fig. E)
To drive collated screws the DCF6201/DCF6202 attachment
should be used. The magazine attachment allows for faster work
flow when driving multiple screws. Instruction for installation,
usage and cleaning of this attachment is included in the
attachment's supplied manual.
MAINTENANCE
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
.
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Nosecone Maintenance (Fig. A, C)
If the nose cone
contaminated with drywall dust.
1
.
4
becomes hard to turn it may be
English
11
Advertisement
Table of Contents
