Advertisement
Quick Links
Advertisement
Summary of Contents for GAUSSIAN ROBOTICS Vacuum 40
- Page 1 Maintenance Guide Vacuum 40 Technical support & operation center...
- Page 2 Content Appearance Cleaning Air filter replacement Dust-mop cloth cleaning Dust bag replacement Dust box and guide plate cleaning Roller brush replacement Roller brush cleaning Side brush replacement Side brush cleaning Dust-mop cloth replacement Charging pile cleaning...
- Page 3 Maintenance guide – Appearance cleaning Vacuum 40 [Switch robot to manual mode] [Push robot to maintenance site] [Wipe the appearance] Click the float button in the lower right Use wet and lint-free wipe to clean the corner and select manual operation.
- Page 4 Maintenance guide – Appearance cleaning Vacuum 40 [Clean the sensors outside] [Clean front horizontal laser] [Clean top-view camera and tablet] Use soft, clean and lint-free wipe to clean the Use soft, clean and lint-free wipe to clean top-view laser, camera and sensor.
- Page 5 Maintenance guide – Dust-mop cloth cleaning Vacuum 40 [Switch robot to manual mode] [Push robot to maintenance site] [Take off dust-mop plate] Click the float button in the lower right Open the rear shell and take off the dust- corner and select manual operation.
- Page 6 Maintenance guide – Dust-mop cloth cleaning Vacuum 40 [Clean the dust-mop cloth] [Assemble the cloth back] Wash the dust-mop cloth. Airing and dry it. Prepare a clean cloth, and assemble it to the plate, then put the plate back to robot.
- Page 7 Maintenance guide – Dust box and guide Vacuum 40 plate cleaning [Switch robot to manual mode] [Push robot to maintenance site] [Open side shell and take out dust box] Click the float button in the lower right Take out the dust box and trash the corner and select manual operation.
- Page 8 Maintenance guide – Dust box, guide plate, Vacuum 40 driving wheel cleaning [Install guide plate] [Dust box] [Driving wheel] There are 2 gaps on one side of guide Insert the dust box, close the lower shell Check the shaft of driving wheel, clean any plate.
- Page 9 Maintenance guide – Roller brush cleaning Vacuum 40 [Open the buckle to open the side shell] [Take roller brush out] [Clean roller brush] Unscrew the bolt of roller brush. The cover Clean the side cover of roller brush. plate will spring up when the bolt was Clean the debris wrapping on the roller unscrewed.
- Page 10 Maintenance guide – Side brush cleaning Vacuum 40 [Take off the side brush] [Clean side brush] Push robot to maintenance site. Press side Clean hair or debris on side brush by brush down by both two hands to take it off.
- Page 11 Maintenance guide – Charging pile cleaning Vacuum 40 [Push robot away from charging pile] [Clean the appearance] Switch robot to manual mode, push it away Unplug the power socket of charging pile from charging pile. and use clean and wet wipe to clean the appearance.
- Page 12 Maintenance guide – Air filter replacement Vacuum 40 [Push robot to maintenance site] [Open the top lid and cover of dust tank] [Put air filter back] Switch robot to manual mode and push it to Open the top lid and open the cover of dust Clean the filter before putting it back.
- Page 13 Maintenance guide – Dust bag replacement Vacuum 40 [Push robot to maintenance site] [Open the top lid and cover of dust tank] [Put dust bag back] Switch robot to manual mode and push it to Open the top lid and open the cover of dust Clean dust bag and put it back.
- Page 14 Maintenance guide – Roller brush Vacuum 40 replacement [Open buckle and side lower shell] [Take roller brush out] [Replace roller brush] Unscrew the bolt of roller brush. The cover Prepare new roller brush. Place the side plate will spring up when the bolt was with gap face-in and insert roller brush into unscrewed.
- Page 15 Maintenance guide – side brush replacement Vacuum 40 [Take side brush off] [Replace side brush] Push robot to maintenance side. Push side Prepare new side brush. Align it to the brush down with both two hands to take it positioning pin and push it forward. It will off.
- Page 16 Maintenance guide – dust-mop cloth Vacuum 40 replacement [Push robot to maintenance site] [Take dust-mop plate off] [Install clean cloth] Switch robot to manual mode and push it to Open rear lower shell and take off dust- Prepare clean cloth. Assemble it to the maintenance site.
- Page 17 Appendix – Daily maintenance checklist Vacuum 40 Daily Maintenance Checklist Weekly Maintenance Chart: ___ /___ /___ to___/___/___ SN:________________________ Check Items Details Monday Tuesday Wednesday Thursday Friday Saturday Sunday Note Side brush has not exceeded its service life Side brush No abnormal wear, no deformation...