Subscribe to Our Youtube Channel
Related Manuals for SteelFlex M3DSM
Summary of Contents for SteelFlex M3DSM
- Page 1 JOONG CHENN INDUSTRY CO., LTD. Sales Office: 3F28, No.5, Shin-Yi Rd., Sec. 5, Taipei, Taiwan 110 R.O.C. Tel: 886-2-27209980 Fax:886-2-27229750 www.steelflexfitness.com M3DSM.1 OWNER'S MANUAL...
- Page 2 M3DSM ASSEMBLY INSTRUCTIONS HARDWARE ILLUSTRATION (A2)HEX BOLT M10X80L PARTIAL THREAD QTY.2 (A5)HEX BOLT M12X20L PARTIAL THREAD QTY.8 (A7)HEX BOLT 1/2"X4-1/2"L PARTIAL THREAD QTY.4 (A8)HEX BOLT 1/2"X12TX3-1/2"L PARTIAL THREAD QTY.6 (A9)HEX BOLT 1/2"X3"L PARTIAL THREAD QTY.12 (A10)HEX BOLT 1/2"X1-1/2"L PARTIAL THREAD QTY.10 inch 1"...
- Page 3 M3DSM ASSEMBLY INSTRUCTIONS HARDWARE ILLUSTRATION (A13)HEX BOLT M10X70L PARTIAL THREAD QTY.16 inch 2" 6" 1" 3" 4" 5" Page M3DSM.1-082013...
- Page 4 M3DSM ASSEMBLY INSTRUCTIONS HARDWARE ILLUSTRATION (B1)NYLON LOCK NUT 1/2" QTY.22 (C4)1/2" BLOT CAP (9212-024) QTY.12 (C5)1/2"(I.D.) CONICAL WASHER QTY.12 (C1) 1/2"(I.D.) FLAT WASHER 34 QTY.42 (C2)M12(I.D.) FLAT WASHER 25 QTY.4 (C6)M10(I.D.) FLAT WASHER 40 QTY.2 (C3)M10(I.D.) FLAT WASHER 27 QTY.16 (C7) 1/2"(I.D.) FLAT WASHER...
- Page 5 M3DSM ASSEMBLY INSTRUCTIONS HARDWARE ILLUSTRATION n n n n 50 End Plug (9211-020) --------------------------------- [2PCS] D2.Ø50 End Plug (9211-074 ) ---------------------------------[8PCS] D3.50X75 End Plug (9211-084) -------------------------------[2PCS] D4. 58X116 End Plug (9211-112) ---------------------------[2PCS] D5. 50X100 End Plug (9211-114) ---------------------------[2PCS] D6. Ø2.5" Rubber Dount (9310-012) -------------------------[2PCS] D7.
- Page 6 M3DSM ASSEMBLY INSTRUCTIONS PARTS ILLUSTRATION SHEET A1[1PCS] B1[1PCS] C1[1PCS] Lables Lable D1[1PCS] E1[1PCS] Lables F1[2PCS] L plate OFFSET Flat end Page M3DSM.1-082013...
- Page 7 M3DSM ASSEMBLY INSTRUCTIONS PARTS ILLUSTRATION SHEET G1[1PCS] H1[1PCS] I1[1PCS] L plate OFFSET Flat end J[2PCS] K[1PCS] P[2PCS] L1[2PCS] M[2PCS] 8313-144 Page M3DSM.1-082013...
- Page 8 M3DSM ASSEMBLY INSTRUCTIONS PARTS ILLUSTRATION SHEET Q[1PCS] 9420-079 R1[2PCS] 8343-276 T[2PCS] 8280-024 S1[2PCS] Ø40X926L 8343-277 U[2PCS] V[2PCS] 8280-025 8280-026 Ø25X1970L Ø25X926L Page M3DSM.1-082013...
- Page 9 M3DSM ASSEMBLY INSTRUCTIONS PARTS ILLUSTRATION SHEET X[1PCS] Y[2PCS] Z[2PCS] 50X1315L plate plate plate AA[1PCS] AB[1PCS] AC[4PCS] 8312-049 stopper this side stopper this side AE[4PCS] AD[2PCS] 8313-204 8312-077 Page M3DSM.1-082013...
- Page 10 M3DSM ASSEMBLY INSTRUCTIONS Above shows STEP 1 assembled and completed Page M3DSM.1-082013...
- Page 11 M3DSM ASSEMBLY INSTRUCTIONS Above shows STEP 2 assembled and completed M10X25L CONE SCREW X 4 PCS Page M3DSM.1-082013...
- Page 12 M3DSM ASSEMBLY INSTRUCTIONS *A10 screw mark on the plate Above shows STEP 3 View A View B assembled and completed NOTE : DO NOT tighten screws A10, A13 till PAGE 13 plate side UPWARD Page 8.1 post D1 Page 8.1...
- Page 13 M3DSM ASSEMBLY INSTRUCTIONS Above shows STEP 4 assembled and completed plate direction INWARD L plate offset L plate offset Flat Ends Page M3DSM.1-082013...
- Page 14 M3DSM ASSEMBLY INSTRUCTIONS NOTE DO NOT tighten screws A2, A13 till PAGE 13 Above shows STEP 5 assembled and completed Page 9.1 POST F1 *A13 plates direction INWARD Page 9.1 POST G1 Page M3DSM.1-082013...
- Page 15 M3DSM ASSEMBLY INSTRUCTIONS Above shows STEP 6 assembled and completed M3DSM.1-082013 Page...
- Page 16 M3DSM ASSEMBLY INSTRUCTIONS tighten 5/16"X3/4"L round allen head screws X 4 pcs pull bars T into Above shows STEP 7 pully sets L1 assembled and completed Note 1. push bars U upward during assembly 2. push pully sets L1 upward during assembly view A tighten 5/16"X5/16"L...
- Page 17 M3DSM ASSEMBLY INSTRUCTIONS Above shows STEP 8 assembled and completed Page M3DSM.1-082013...
- Page 18 M3DSM ASSEMBLY INSTRUCTIONS Detail view Above shows STEP 9 assembled and completed NOTE 1. placing bars J on location A, B , checking GAP and TIGHTNESS between plates 2. aligning bars Y, Z to balance the GAP and TIGHTNESS 3. tighten screws A10, A13 on page 8.2, screws A2, A13 on page 9.2...
Need help?
Do you have a question about the M3DSM and is the answer not in the manual?
Questions and answers