Operators and Maintenance Manual Page 2/15 Display EEM MOT 01 FL01.01 Table of Contents Introduction ..................... 3 General information ................3 Handling in transport and storage ............. 4 Installation ..................5 3.1. Environmental specifications............ 5 3.2. Dimensions ................5 3.3.
Operators and Maintenance Manual Page 3/15 Display EEM MOT 01 FL01.01 Introduction This instrument is intended for ultralight, microlight, homebuilt and experimental aircraft. The purpose of EEM MOT 01 type display is to present key flight information to the pilot. Version FL01.01 displays air speed of the aircraft.
Operators and Maintenance Manual Page 4/15 Display EEM MOT 01 FL01.01 during installation and in its operating phase. This document does not contain rules and guidelines on operation of aircraft instruments at large. Read the manual thoroughly before turning on the instrument and precisely follow the instructions to install and configure it.
Operators and Maintenance Manual Page 5/15 Display EEM MOT 01 FL01.01 3. Installation 3.1. Environmental specifications The EEM MOT 01 display has been designed to be installed in non- hermetic cockpits of ultralight aircrafts of ceiling not exceeding 3 000 m (10 000 ft).
Operators and Maintenance Manual Page 6/15 Display EEM MOT 01 FL01.01 3.3. Mounting The display should be located conveniently within the pilot’s view in the control panel in the cockpit. The diameter of the mounting hole to be cut in the panel is 80mm. It is recommended that the display is installed from the rear side the control panel.
Page 7
Operators and Maintenance Manual Page 7/15 Display EEM MOT 01 FL01.01 The EEM MOT 01 display is connected to the system by in-built MOLEX Ultra-Fit 3.5 mm 6 pin male connector located at the back of the instrument. A schematic diagram of the connection is shown in Figure 4 and in Table 1.
Operators and Maintenance Manual Page 8/15 Display EEM MOT 01 FL01.01 4. Operation and maintenance The display is to be connected to AUX AVS 2. The front panel of EEM MOT 01 is composed of three elements: the display, two status diodes (alert indication), and the encoder knob & push- button for setting parameters (Fig.
Page 9
On client’s request, warning and alarm threshold values may be set for some of the above parameters according to the specification provided by the aircraft supplier. Default threshold values are listed in Table 2. Tab. 2. Parameters displayed by EEM MOT 01 FL01.01 display Symbol/ Range of...
Page 10
Operators and Maintenance Manual Page 10/15 Display EEM MOT 01 FL01.01 Fig. 7. The idea of flight parameter status information Thus, information on the status of a flight parameter is presented in two ways: 1) by means of the colour of two status diodes according to the...
Operators and Maintenance Manual Page 11/15 Display EEM MOT 01 FL01.01 – alarm; 2) by means of the colour of digits and bar graph (if applicable) presenting the value of the parameter: green – flight parameters within normal range; orange –...
Operators and Maintenance Manual Page 12/15 Display EEM MOT 01 FL01.01 5.3. Cleaning and conservation The screen is to be buffed with water-damped soft cloth. Optionally, if very dirty, can be cleaned with cloth sparingly damped with mild soap solution or with a liquid dedicated for liquid crystal displays.
Operators and Maintenance Manual Page 13/15 Display EEM MOT 01 FL01.01 5.5. Repairs Repairs and inspections of the instrument can be conducted only by its manufacturer. The display does not contain any user-serviceable parts. Unauthorized repairs or modifications may result in permanent damage to the equipment and void the warranty.
Page 14
Operators and Maintenance Manual Page 14/15 Display EEM MOT 01 FL01.01 3. Auto & Aero Technologies Sp. z o.o. warrants this product for 12 months from date of purchase. 4. Auto & Aero Technologies Sp. z o.o. will, at its sole option, repair or replace any components that fail in normal use.
Page 15
Operators and Maintenance Manual Page 15/15 Display EEM MOT 01 FL01.01 The information in this document is subject to change without notice and should not be construed as commitment by Auto & Aero Technologies Sp. z o.o. These technical data and the information embodied therein are the property of Auto &...