Table of Contents
Advertisement
@ AC POWER PLUG
Never connect the AC power plug until assembly has been
completed!
center of the arm lift bar. Pushing down on this curved bar will
make the screw accessible.
Clockwise rotation ...Arm height lowers.
Counterclockwise rotation...Arm height raises.
@ STROBO ILLUMINATOR/PILOT LAMP @ ANTI-SKATING FORCE CONTROL
This dual-function illuminator is lit only when the player is "on"
and the turntable platter is rotating.
VARIABLE PITCH CONTROLS
adjusted within a range of 10%
SPEED ADJUSTMENT SCREWS
If, for any reason, the adjustment cannot be successfully made
counterclockwise with a (—), tip screw driver.
Counterclockwise...
The rotation will be speeded up.
and re-adjustment will not be necessary.
The turntable platter of this set also works as part of the rotor
of the motor. Never remove the turntable platter unnecessarily.
Never stick dust or iron filings to adhere to the magnet rotor.
These strobo dots, set on the tapered rim of the turntable platter
to make strobo
reading easier, are divided into four
and 45 r.p.m.) at 50 Hz and 60 Hz AC as follows
45 r.p.m. at 0 Hz
93-1/3 r.p.m. at 50 Hz
45 r.p.m. at 60 Hz
33-1/3 r.p.m. at 60 Hz
@ TONEARM RETURN ADJUSTMENT
SCREW
In some cases, the tonearm will tend to return to its rest position
before the record has finished playing. In other cases, it will to
return to the rest position even after the record has finished
Rotation of this screw in the proper direction will correct either
condition.
Clockwise rotation ...The tonearm will return to rest lat
Counterclockwise rotation...The tonearm will return to rest ear-
To be adjusted if the tonearm fails to set down at the right start-
ing point at the beginning of the record. For access to the
screw, a rubber cap above it must be removed.
Clockwise rotation
...This will move the set-down point out-
ward, away from the record center.
Counterclockwise rotation...This will move the set-down point
inward toward the record center.
® ARM LIFT ADJUSTMENT SCREW
When the tonearm is removed from the record surface via the
tonearm lift, the space between the stylus tip and the record
surface should be between 5 and 10 mm (between 3/16" and
25/64"), If this height needs adjustment, turn the screw along the
KNOB
Turn this knob to the same number as the stylus pressure ring
indicates.
Skating force is the frictional force caused by contact between
the tip of the stylus and the record groove, and is applied to the
stylus as a side pressure depending upon the relationship of the
geometrical position of the tonearm.
This force results in an unbalance of the contact pressure be-
tween the stylus tip and each groove wall of the record, an
increase of distortion, a decrease of separation characteristics
and abnormal wear of the stylus tip and the record grooves.
For this reason, it is necessary to compensate this skating force.
This anti-skating force mechanism performs this compensation
function.
The quantity of anti-skating force is in proportion to the stylus
pressure and, therefore, it should be adjusted according to the
stylus pressure.
Move this lever downward or upward, then the tonearm will
descend or ascend on the record surtac
Downward movement... The tonearm will descend slowly on the
record surface and resume playing in
the same groove.
The tonearm will raise from the record
surface and interrupt playing.
Set this knob to the desired number of times you want.
(R) is continuous play.
Set this knob to the diameter of the record to be played.
@ START/STOP LEVER
Pull this lever for automatic start and stop functions,
NOTE
If the MEMO-REPEAT knob is set to the other positions than (0),
then the unit will not shut off and will continue playing until the
times which you set.
2 BEFORE USING
@ CHECK THE PARTS
Player unit
i
e
Turntable platter
F
:
Turntable sheet
Dust cover.
45 r.p.m. adaptor
Special oi
Screws (for cartridge) (long).
Screws (for cartridge) (short)
Auxiliary weight
@ REMOVE THE TRANSIT SCREWS
Remove the two screws for transformer and place them in the
screwing holes for future use, as when the player must again be
transported.
@ APPLY TWO OR THREE DROPS OF OIL TO THE MOTOR SHAFT
To lubricate, open the tip of the vessel with a needle, and
apply two or three drops of oil to the motor shatt. (See Fig. 1)
@ REMOVE THE PROTECTING COVER OF THE ROTOR OF THE
TURNTABLE PLATTER
NoTE
NEVER CONNECT THE AC POWER PLUG UNTIL THE ASSEMBLY
HAS BEEN MADE!
Upward movement,
Advertisement
Table of Contents
