Page 1
Owner’s Manual Legacy Series 305 LP, 500 ASM, 750 ASM, 1000 ASM, 1600 ASM, Automated Power Bundle Voigt Smith Innovation, LLC 23371 610th Avenue Madison Lake, MN 56063...
Page 2
One year - All other parts * on your equipment are warrantied against defects through VSI for one year from the date of purchase. (*NOTE: There is no warranty on pump seals as these are normally caused due to improper use or running pumps dry.
Table of Contents Introduction Important Information Charge Battery Before First Use Pumps Seals and Running Your Pump Dry Safety While Operating Parts Overview Total Control Flowmeter Proportional Valve Filter Pile Driver Boom Emergency Back Up Harness Installation and Setup Installing Your Sprayer Assembling Your Pile Driver Boom Installing Your Boom Camlocks (Initial) Boom Tip Positions Small, Medium, Large...
Page 4
Boom Section Control ACC Tab of App Throttle and Choke Control Engine Start Engine Stop Hose Reel Rewind Control Details Tab Job Tracking/Reporting Profile Tab Maintenance Before Initial Operation Check Your Tank Straps! Checking the Engine Oil Level Adding Fuel to Engine Maintenance Checks Valve Positions Suction Side Vs Pressure Side...
A digital version of this manual that can Figure 1 be accessed on the VSI Spray Control app (“Getting Started/FAQ” button on The batteries do not come fully charged the Profile” tab).
(see Pay attention to the road while driving and next item). The image below shows your operating the VSI Spray Control app. flow meter as viewed from the back of your spray unit. These magnetic flow...
5.0. If your unit is equipped with precision. Each section of the with a red proportional valve, adjust the boom is controlled via the VSI Spray sprayer’s PID Speed in the settings to Control app by pressing the Boom 1.5.
Ensure that the unit is properly secured when needed. Connect the harness to the to the truck. VSI carries no liability for ten pin plug located on the back of the improper installation of the unit.
Installing Your Boom Camlocks (Initial) A roll of 1” hose and a bag of barbed camlock parts and hose clamps is included with each spray unit as shown in Figure 3. A simple walkthrough video of installing the boom cam locks is on our YouTube channel: www.youtube….
Large Nozzles this is because of the high rate of speed at which they travel on roadways requiring a heavier jet pattern to not get The post treatment tips are the top ones diluted in the wind, plus they have very on each end and the central boom with high traffic levels from cars to track the a vertical camlock in the middle that...
If the light is flashing one of these Operating colors that means that one or more of the booms is on or Hose Reel Procedures Tracking is enabled. The color of the light indicates the battery voltage Control Box Light Modes that the computer is currently reading from the battery.
Make sure that after any settings VSI employee first. changes or tank reset you hit the “Save” button at the bottom right of the screen Tank Size - The tank size is...
Spray Tab and open all signaled valve sections once the vehicle begins moving again. The Spray tab of the app is where all Tip - If the application vehicle is not functions of the application process are moving the valves will NOT open when controlled.
recommended the user hits this button Boom Section Control everytime the hose reel is used, even if you are not tracking the amount of liquid At the bottom of the screen you will find applied. your Boom Section Control buttons. These control your left, center, and right Ice Buster nozzles.
down until the engine has stopped stop the job. The job will then be saved running to shut down the engine. until the user is ready to submit the report. Hose Reel Rewind Control When the user selects the Submit Report function, the user will be The bottom button on the ACC tab of prompted to supply an email address to...
Checking the Engine Oil Profile Tab Level The profile tab is used to search and Your VSI sprayer is equipped with a connect to WiFi networks. Reference GX200 Honda engine. Checking the the Connecting to WiFI section of the engine oil follows the same procedure manual.
It is also important to keep your sprayer for your sprayer or hose reel to work clean of all salt residue. Frequently correctly. washing your sprayer will prolong the life of all of the components. Tip - The next most common mistake is that the tank valve (back left of image) Valve Positions gets left closed.
being deadheaded) but it will take an pump-out to work, but it will be exceptionally long amount of time substantially slower than if it is set up through that bypass. If the tank you are properly as shown. pulling liquid from is lower than the height of the pump, you may have to prime the pump by unscrewing the top cap on the pump and allowing the air...
application will require that the engine especially on the boomless nozzles be at 75% or 100% throttle. spray pattern. Continue spraying until the desired area Application has been covered. Now that the engine is running, Manual Mode Display application can begin! Select the Spray tab on the app.
Pairing the Remote function, control engine speed and choke position, and rewind the hose reel. The VSI remote must be paired with the sprayer. The process for pairing is as Remote Functions follows 1. Turn on the remote by pressing The remote operates in three different and holding the power button.
Tip - The remote will automatically shut down after 15 minutes of inactivity to Only Remote Connected conserve battery life. The VSI remote is able to control the After Season Care sprayer in situations where a smartphone or tablet are not connected.
run the motor to ensure proper off FAQs/ season storage of fuel. Troubleshooting Tip - The drain plug located on the bottom of the pump can be removed to Potential Reason for drain excess water from the pump Fuses Blowing during storage.
Page 24
Voigt Smith Innovation LLC 150 East Sharon Street Le Center, MN 56057 www.vsinnovation.com Main Office: 507-252-3033 Email: sales@vsinnovation.com...
Need help?
Do you have a question about the Legacy Series and is the answer not in the manual?
Questions and answers