Advertisement
SG-S151 Overview
Front View
420
SG-S171 Overview
Front View
450
SG-S211 Overview
Front View
590
Quick Setup
Installing VESA Mount
Installing Stand Kit
Handle
Stand Kit
The following messages are reminders for safety on how to protect your system from damages and extend a long life of the system.
1. Check the Cable Voltage
•
The range of operating voltage should be DC 12V /24V. Otherwise, the system could be damaged.
2. Environmental Conditions
•
Place your SG-S151/SG-S171/SG-S211 on a sturdy, level surface. Be sure to allow enough space to have easy access around
the system.
•
Avoid extremely hot or cold place to install the system.
•
Avoid exposure to sunlight for a long period of time or in an airtight space.
•
Avoid the system from any heating device or using the system when it's been left outdoors in a cold winter day.
•
Bear in mind that the operating ambient temperature is from 0°C ~ 40°C for HDD & 0°C ~ 50°C for SSD.
•
Avoid moving the system rapidly from a hot place to a cold place and vice versa because condensation may come from inside
of the system.
•
Placing the sy in strong vibrations may cause hard disk failure.
•
Don't place the system close to any radio-active device in case of signal interference.
Rear View
385
100
160
Rear View
17.5
415
M4 screw
(Depth: 8mm)
100
175
Rear View
550
20
M4 screw
(Depth: 8mm)
100
245
Wall
side hole
Step 1. Attach Panel PC onto Stand Kit and align the side holes on the rear
of Panel PC with the upper holes of the Stand Kit.
upper hole of Stand Kit
Step 2. Fasten the two handles into the side holes of the Stand Kit
to secure the system and complete.
Safety Precaution
Side View
Top View
Antenna
70
30
Hole
Bottom View
Side View
Top View
Antenna
30
Hole
40
Bottom View
70
Side View
Top View
Antenna
Hole
30
40
Bottom View
70
VESA Mount Accessories
VESA Mount
Stand Installation Accessories
3. Handling
•
Do not turn the system upside down. This may cuase the hard drive to mal-function.
•
Avoid putting heavy objects on top of the system.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
• Never use strong agents such as benzene and thinner to clean the system.
• If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special vacuum cleaner for computers.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly recommend that qualified engineers
can open and disassemble the system. Please handle LCD and Touchscreen with extra care as they are easily breakable.
Rear I/O View
Antenna
Hole
DC IN
Power
COM
Button
DC IN
I/O Ports
Rear I/O View
Antenna
Hole
DC IN
Power
COM
Button
DC IN
I/O Ports
Rear I/O View
Antenna
Hole
DC IN
Power
COM
Button
DC IN
I/O Ports
VESA Mount Kit x 1
Handle x 2
Stand Kit x 1 + Screw x 4
All Rights Reserved. Copyright 2020
(Unit: mm)
LAN1
VENT
LAN2
COM
LAN
LAN
USB
USB
VENT
2 x USB Ports
LAN1
VENT
LAN2
COM
LAN
LAN
USB
USB
VENT
2 x USB Ports
LAN1
VENT
LAN2
COM
LAN
LAN
USB
USB
VENT
2 x USB Ports
Advertisement
