Pioneer VSX-95 Operating Instructions Manual page 21

"FRONT PANEL FACILITIES
NOTE:
¢ The system searches for stations within successive 1 MHz ranges
for FM and 100 kHz ranges for AM. During DIRECT ACCESS tuning,
it searches up and down for a station until it reaches the edges of
the band. If no receivable station is found within the band range, the
receiver returns to the state it was in before the HITS button was
pressed.
/f the upper (or lower} frequency limit of the receiver is encountered
during HITS operation, the receiver stops searching in that direction
but continues to search in the other.
INPUT SELECTOR buttons
* Video input selector
VCR 1: Press when performing playback on a first VCR unit.
VCR 2: Press when performing playback on a second VCR unit.
VCR 3: Press when performing playback on a third VCR unit.
LD: Press when performing playback on an LD player.
TV: Press to watch TV broadcasts from the TV tuner connected to the
rear panel TV IN jacks. :
VIDEO: Press when performing playback on a VCR connected to VIDEO
IN jack.
* Audio input selector
TAPE 1/DAT: Press when performing playback on a DAT or cassette
deck.
TAPE 2 MONITOR: Press when performing playback on a second
cassette deck.
LINE: Press when performing playback on an audio component
connected to the LINE IN jacks.
CD: Press when playing compact discs on a CD player.
TUNER: Press when listening to radio broadcasts.
PHONO: Press when playing records on a turntable.
NOTE:
Because of the digital processing performed by this unit's Digital Signal
Processor, high level input may result in distortion. This is particularly
true when using a turntable with a high output cartridge. In this case,
adjust the volume evel with the PHONO LEVEL control on the rear panel
so that it is the same as other inputs. If there is distortion due to
excessively high input level from another component, use the INPUT
ATT button to adjust input level.
BALANCE buttons
Use to adjust the sound volume balance between left and right speakers.
L: Press to decrease the sound on the right side.
R: Press to decrease the sound on the left side.
Press L and R together to bring the volume balance back to standard
(Left = Right).
Example: When pressing and holding the "'R'' button.
py gi Gi ! vy o : a
ini if a i) i iad my ius in eneet
—
@) Tone control buttons
BASS:
Use to adjust the low-frequency level. Press the + button to increase
low-frequency level; and the — button to decrease it.
When both sides (+, —) of the BASS control are pressed
simultaneously, the base response will be set to the flat (normal)
condition. ''BASS C" is shown in the display section.
TREBLE:
Use to adjust the high-frequency level. Press the + button to increase
high-frequency level, and the — button to decrease it.
When both sides (+, —) of the TREBLE control are pressed
simultaneously, the treble response will be set to the flat (normal)
condition. '" TREBLE C'' is shown in the display section.
Adjust TONE CONTROL settings are indicated in the display section for
several seconds.
62 REC SELECTOR button
You can select the component to be recorded from, on TAPE 1, VCR 1,
VCR 2, without using the INPUT SELECTOR.
Each time you press the REC SELECTOR button, the components
change in the following order.
[_ TUNER — PHONO — VCR 1*— VCR 2*—> VCR 3— ad)
CD LINE «TAPE 1* «VIDEO = TV
When the REC SELECTOR has been through all the components once,
REC SELECTOR switches off.
Recording between units marked with the ''*'' is possible in the
foliowing relationships.
From TAPE 1 on VCR 1 and 2, from VCR 1 on VCR 2 and TAPE 1,
and from VCR 2 on VCR 1 and TAPE 1.
Do not select the component you wish to record on (for example,
VCR 1), with the REC SELECTOR.
@) V (Video) SIGNAL SELECTOR button
Press this to switch VIDEO OUT (TO MONITOR TV) and VCR VIDEO
OUT in the following sequence: (Audio does not change)
VCR 1— VCR 2+ VCR 3 LD TV VIDEO——
ae ee
Indications are only displayed during operation.
There is no picture when it is OFF.
@ ENHANCER OFF/ON button (See page 34)
Use to switch the video enhancer effect ON/OFF during playback or
recording of a video.
When it is switched ON, adjust the degree of effect with the JOG dial ®.
If you turn ON the SPLIT SCREEN OFF/ON button @, the right half of
the screen shows a picture with the enhancer ON, and the left half of
the screen shows a picture with the enKancer OFF.
The enhancer has no effect on S jack and MULTI-ROOM & SOURCE
VIDEO OUT jack video signals. .
@ VCR 3 INPUT jacks
Video components such as a VCR or TV camera, etc. can be connected
here.
@ JOG MODE button
Use this to select the mode you want to control with the JOG dial @.
The selected mode is indicated by the JOG MODE indicators @.
@? Reset button
Use this when normal operation becomes impossible because of extemal
influences such as static electricity or lightning, or when operation is
impossible even when operation buttons are pressed. Press this button
to return to normal operating conditions.
if you press this button when the power is ON, the unit switches to
POWER STANDBY, and the entire contents of the memory are erased.
21
<ARB1333>