Subscribe to Our Youtube Channel
Related Manuals for Plymovent ECONOMY ARM
Summary of Contents for Plymovent ECONOMY ARM
- Page 1 Extraction arm (hose tube arm) ECONOMY Installation and user manual www.plymovent.com...
-
Page 2: Table Of Contents
To improve comprehension for people whose first language is not English, we have written parts of this manual in Simplified Technical English (STE). STE is a controlled language originally developed for aerospace industry maintenance manuals. It offers a carefully limited and standardized subset of English, along with specific writing rules. 0000101886/161121/A Economy Arm... -
Page 3: Preface
Refer to Fig. I on page 9. General description Pressure drop The Economy Arm (EA) is a hose tube arm with a spring Refer to Fig. II on page 9. balanced internal support mechanism. The hood has a safety mesh and a control valve and is 90° movable in four Refer to the available product data sheet for directions. -
Page 4: Product Description
Operating the machine within the limits of its intended use also involves observing the instructions in the user H types only manual. 0000101886/161121/A Economy Arm... -
Page 5: Installation
Protect the product against water and humidity. • Make sure the room is always sufficiently ventilated; this There are different ways to install the Economy Arm. applies especially to confined spaces. Fig. III on page 9 gives a summary of the relevant paragraphs per arm type (specifically H and •... - Page 6 Put the locknut M20 (A) on the hinge rod (E) and tighten it. • Install the assembly to the wall bracket with the 8 bolts Mounting to/on Position M6x25 + washers M6. Floor vertical Ceiling Wall horizontal 0000101886/161121/A Economy Arm...
- Page 7 Put the washer M20 (E) on the rotating flange (F). • Put the hinge rod (B) in the rotating flange (F). Suitable types: refer to paragraph 1.4 • Put the hose (A) over the arm swivel ring (D). The bolts are supplied with the arm 0000101886/161121/A Economy Arm...
-
Page 8: Use
Turn off the connected extraction fan or system approx. 20 seconds after finishing welding. 180° 180° D (2x) D (2x) E (2x) A = max. 480 mm (19 in.) B = >480 mm (19 in.) Fig. 5.2 Correct position of the hood Fig. 4.8 Hood mounting 0000101886/161121/A Economy Arm... -
Page 9: Maintenance
After life of the product, dispose of it in accordance • Adjust the friction; refer to the images below for the with federal, state or local regulations. adjustment points. Swivel bracket “H” types “S” types Middle hinge 0000101886/161121/A Economy Arm... - Page 10 4.6 par. 4.6 par. 4.6 EconomyArm-3/H rm-2/H EconomyArm-4/H EconomyArm-3/H EconomyArm-4/H EconomyArm-4/H EA-2/H EA-3/H EA-4/H R962 R1449 R1914 63° 63° 63° 2346 7½ 3291 4296 2000 6½ 2000 6½ 2000 6½ 2300 7½ 2300 7½ 2300 7½ 0000101886/161121/A Economy Arm...
- Page 11 ANNEX Fig. IV Mounting examples “H” types Economy Arm + FUA Economy Arm + PA-110 Economy Arm + FUA + Economy Arm + PA-220 PA-220 Fig. V Mounting examples “S” types Economy Arm + PA-110 Economy Arm + PA-220 Economy Arm + PA-220...
- Page 12 MATERIAL: - The information contained in this drawing is the sole property of 4x M12 lock nut ® PLYMOVENT. Any reproduction in part GENERAL TOLERANCES: - 3RD ANGLE PROJECTION MATERIAL: - The information contained in this or as a whole without written permission drawing is the sole property of of PLYMOVENT is prohibited.
- Page 13 ANNEX Fig. VII Dimensions and mounting measurements of the wall bracket 11¾ 2 - 2,3 6½ - 7½ 10⅝ 15⅛ 10⅜ Ø 13 9000 N 3⅞ 9½ 0000101886/161121/A Economy Arm...
- Page 14 ANNEX Fig. VIII Exploded view 0000101944 0000101537 0000101917 0000101918 0000101919 0000101903 0000102989 0000101395 0000101912 0000101912 (2x) 0000101908 0000102409 0000101550 0000101911 0000101937 0000101886/161121/A Economy Arm...
- Page 15 Rubber collar Ø 160 mm EA-2 0000101917 Hose L=2500 mm/Ø 163 mm, incl. 2 hose clamps EA-3 0000101919 Hose L=3500 mm/Ø 163 mm, incl. 2 hose clamps EA-4 0000101918 Hose L=4500 mm/Ø 163 mm, incl. 2 hose clamps 0000101886/161121/A Economy Arm...
- Page 16 0000101886/161121/A Economy Arm www.plymovent.com...
Need help?
Do you have a question about the ECONOMY ARM and is the answer not in the manual?
Questions and answers