Related Manuals for EINHELL TC-AG 100/750
Summary of Contents for EINHELL TC-AG 100/750
- Page 1 TC-AG 100/750 Original operating instructions Angle grinder Art.-Nr.: 44.309.64 I.-Nr.: 21010 Anl_TC_AG_100_750_EX_PH_SPK7.indb 1 Anl_TC_AG_100_750_EX_PH_SPK7.indb 1 03.11.2020 13:34:28 03.11.2020 13:34:28...
- Page 2 - 2 - Anl_TC_AG_100_750_EX_PH_SPK7.indb 2 Anl_TC_AG_100_750_EX_PH_SPK7.indb 2 03.11.2020 13:34:29 03.11.2020 13:34:29...
- Page 3 - 3 - Anl_TC_AG_100_750_EX_PH_SPK7.indb 3 Anl_TC_AG_100_750_EX_PH_SPK7.indb 3 03.11.2020 13:34:31 03.11.2020 13:34:31...
- Page 4 - 4 - Anl_TC_AG_100_750_EX_PH_SPK7.indb 4 Anl_TC_AG_100_750_EX_PH_SPK7.indb 4 03.11.2020 13:34:33 03.11.2020 13:34:33...
-
Page 5: Safety Regulations
Danger! liquids, gases or dust. Electric tools produ- When using the equipment, a few safety pre- ce sparks which could set the dust or vapours cautions must be observed to avoid injuries and alight. damage. Please read the complete operating c) Keep the electric tool out of the reach of instructions and safety regulations with due care. - Page 6 tool is switched off before you connect caused by badly maintained electric tools. it to the power supply and/or insert the Keep your cutting tools sharp and clean. battery, or pick up or carry the tool. If your Carefully maintained cutting tools with sharp fi...
- Page 7 fl ange. Plug-in tools that are not exactly se- standstill. The rotating plug-in tool may cured to the electric tool will rotate irregularly, come into contact with the surface on which vibrate a great deal and might result in you you place it which could result in you losing losing control.
- Page 8 tor can manage the recoil and reaction forces e) Always use undamaged clamping fl anges by taking suitable precautions. of the correct size and shape for the b) Never move your hand into the vicinity of grinding/sanding wheel you have selec- rotating plug-in tools.
-
Page 9: Layout And Items Supplied
2. Layout and items supplied case of misuse. The user / operator and not the manufacturer will be liable for any damage or inju- ries of any kind caused as a result of this. 2.1 Layout (Fig. 1) 1. Spindle lock Please note that our equipment has not been de- 2. -
Page 10: Before Starting The Equipment
6. Operation 3. Health damage caused by hand-arm vib- rations if the equipment is used over a pro- longed period or is not properly guided and 6.1 Switch (Fig. 4) maintained. The angle grinder comes with a safety switch which is designed to prevent accidents. To switch on, press down the On/Off... -
Page 11: Replacing The Power Cable
• b) Flange nut Never use a cutting wheel for rough grin- • Flange arrangement when using a straight ding. cutting wheel (Fig. 9) • a) Clamping flange • b) Flange nut 7. Replacing the power cable 6.4 Motor Danger! It is vital for the motor to be well ventilated during If the power cable for this equipment is damaged, operation. -
Page 12: Disposal And Recycling
8.4 Ordering replacement parts: Please quote the following data when ordering replacement parts: • Type of machine • Article number of the machine • Identification number of the machine • Replacement part number of the part required 9. Disposal and recycling The equipment is supplied in packaging to pre- vent it from being damaged in transit. -
Page 13: Warranty Certificate
5. To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identifi... - Page 14 - 14 - Anl_TC_AG_100_750_EX_PH_SPK7.indb 14 Anl_TC_AG_100_750_EX_PH_SPK7.indb 14 03.11.2020 13:34:34 03.11.2020 13:34:34...
- Page 15 - 15 - Anl_TC_AG_100_750_EX_PH_SPK7.indb 15 Anl_TC_AG_100_750_EX_PH_SPK7.indb 15 03.11.2020 13:34:34 03.11.2020 13:34:34...
- Page 16 EH 11/2020 (01) Anl_TC_AG_100_750_EX_PH_SPK7.indb 16 Anl_TC_AG_100_750_EX_PH_SPK7.indb 16 03.11.2020 13:34:34 03.11.2020 13:34:34...