Related Manuals for EINHELL TC-AG 100
Summary of Contents for EINHELL TC-AG 100
- Page 1 TC-AG 100 Original operating instructions Angle grinder Art.-Nr.: 44.306.71 I.-Nr.: 21010 Anl_TC_AG_100_EX_PH_SPK7.indb 1 Anl_TC_AG_100_EX_PH_SPK7.indb 1 28.10.2020 11:21:33 28.10.2020 11:21:33...
- Page 2 - 2 - Anl_TC_AG_100_EX_PH_SPK7.indb 2 Anl_TC_AG_100_EX_PH_SPK7.indb 2 28.10.2020 11:21:34 28.10.2020 11:21:34...
- Page 3 - 3 - Anl_TC_AG_100_EX_PH_SPK7.indb 3 Anl_TC_AG_100_EX_PH_SPK7.indb 3 28.10.2020 11:21:36 28.10.2020 11:21:36...
- Page 4 Danger! - Read the operating instructions to reduce the risk of inquiry Caution! Wear ear-muff s. The impact of noise can cause damage to hearing. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials.
-
Page 5: Safety Regulations
Danger! b) Avoid bodily contact with earthed sur- When using the equipment, a few safety pre- faces such as pipes, heating, ovens and cautions must be observed to avoid injuries and fridges. The risk of electric shock is increa- damage. Please read the complete operating sed if your body is earthed. - Page 6 circumstances. 5. Service Wear suitable work clothes. Do not wear a) Have your electric tool repaired only by loose clothing or jewellery. Keep hair, clo- trained personnel using only genuine thes and gloves away from moving parts. spare parts. This will ensure that your elec- Loose clothing, jewellery or long hair can get tric tool remains safe to use.
- Page 7 checked and fi tted the plug-in tool, make risks. sure that you and other persons in the o) Never use the electric tool in the vicinity vicinity are not on a level with the rotating of infl ammable materials. Sparks may igni- plug-in tool and allow the electric tool to te these materials.
-
Page 8: Layout And Items Supplied
tool does not bounce off or jam in the Other special safety information for cutting- workpiece. off wheels At corners, sharp edges or if it bounces, the a) Avoid blocking the cutting-off wheel or rotating plug-in tool will tend to jam. This will applying excessive contact pressure. -
Page 9: Proper Use
4. Technical data 2.2 Items supplied Please check that the article is complete as specifi ed in the scope of delivery. If parts are Mains voltage: ....... 220 V ~ 60 Hz missing, please contact our service center or the Power input: .......... -
Page 10: Before Starting The Equipment
5. Before starting the equipment 6. Operation Before you connect the equipment to the mains 6.1 Switch (Fig. 4) supply make sure that the data on the rating plate The angle grinder comes with a safety switch are identical to the mains data. which is designed to prevent accidents. -
Page 11: Replacing The Power Cable
7. Replacing the power cable 6.4 Motor It is vital for the motor to be well ventilated during operation. Be sure, therefore, to keep the ventilati- Danger! on holes clean at all times. If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its 6.5 Grinding Wheels after-sales service or similarly trained personnel... -
Page 12: Disposal And Recycling
9. Disposal and recycling The equipment is supplied in packaging to pre- vent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. -
Page 13: Warranty Certificate
5. To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identifi... - Page 14 - 14 - Anl_TC_AG_100_EX_PH_SPK7.indb 14 Anl_TC_AG_100_EX_PH_SPK7.indb 14 28.10.2020 11:21:38 28.10.2020 11:21:38...
- Page 15 - 15 - Anl_TC_AG_100_EX_PH_SPK7.indb 15 Anl_TC_AG_100_EX_PH_SPK7.indb 15 28.10.2020 11:21:39 28.10.2020 11:21:39...
- Page 16 EH 10/2020 (01) Anl_TC_AG_100_EX_PH_SPK7.indb 16 Anl_TC_AG_100_EX_PH_SPK7.indb 16 28.10.2020 11:21:39 28.10.2020 11:21:39...
Need help?
Do you have a question about the TC-AG 100 and is the answer not in the manual?
Questions and answers