Summary of Contents for Siemens RUGGEDCOM WIN5151-V-GPS
Page 1
Preface Introduction Installing the Subscriber Station RUGGEDCOM WIN5151-V-GPS Technical Specifications Dimension Drawings Certification Installation Guide 01/2018 RC1331-EN-01...
Page 2
Warranty Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void.
Preface Preface This guide describes the RUGGEDCOM WIN5151-V-GPS. It describes the major features of the subscriber station, installation, commissioning and important technical specifications. It is intended for use by subscriber station installers and operators, and assumes readers have a working knowledge of WiMAX technologies and procedures.
Siemens Sales representative. Customer Support Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general information, contact Siemens Customer Support through any of the following methods: Online Visit http://www.siemens.com/automation/support-request...
Installation Guide Introduction Introduction The RUGGEDCOM WIN5151-V-GPS subscriber station (also referred to as Customer Premises Equipment) is part of the RUGGEDCOM WIN family, a line of mobile WiMAX broadband wireless access systems based on the IEEE 802.16e mobile WiMAX standard.
The subscriber station supports both IP convergence sublayer for wireless Internet service providers or Ethernet Convergence Sublayer, ideal for mission critical private networks. Section 1.2 Description The RUGGEDCOM WIN5151-V-GPS features various ports, controls and indicator LEDs on the bottom panel for connecting, configuring and troubleshooting the subscriber station. RSSI W.LINK PWR Figure 1: RUGGEDCOM WIN5151-V-GPS...
Page 9
RUGGEDCOM WIN5151-V-GPS Chapter 1 Installation Guide Introduction RSSI Level -75 to -80 -70 to -75 -65 to -70 -20 to -60 > -20 W.LINK LED Indicates when the subscriber station is connected with a base station. State Description Green (Solid) Subscriber station is connected to the base station and receiving services.
WARNING! Safety hazard – risk of serious personal injury and/or damage to equipment. Installing the RUGGEDCOM WIN5151-V-GPS can pose a serious safety hazard. Be sure to take precautions to avoid the following: • Exposure to high voltage lines during installation •...
Chapter 2 RUGGEDCOM WIN5151-V-GPS Installing the Subscriber Station Installation Guide IMPORTANT! This product should be installed in a restricted access location where access can only be gained by authorized personnel who have been informed of the restrictions and any precautions that must be taken.
Verify all items are included. If any item is missing or damaged, contact Siemens for assistance. Section 2.3 Required Tools and Materials The following tools and materials are required to install the RUGGEDCOM WIN5151-V-GPS: Tools Greases • Wrench or socket set •...
Chapter 2 RUGGEDCOM WIN5151-V-GPS Installing the Subscriber Station Installation Guide Section 2.4 Site Preparation and Precautions Before installing the subscriber station and or antenna(s), it is important to plan the the complete installation and make sure the appropriate safe guards are in place.
Do not attempt to touch or remove the component. Section 2.5 Mounting the Subscriber Station The RUGGEDCOM WIN5151-V-GPS is designed for maximum mounting and display flexibility. It can be secured to a bracket and then mounted to a pole, wall or tower. NOTE For detailed dimensions of the subscriber station, refer to Chapter 4, Dimension...
Chapter 2 RUGGEDCOM WIN5151-V-GPS Installing the Subscriber Station Installation Guide Section 2.5.1 Mounting the Subscriber Station to a Wall or Tower Mount the subscriber station to any wall or tower capable of supporting its weight. An outer wall on a roof or other high location to avoid interference from other buildings or trees is preferred.
RUGGEDCOM WIN5151-V-GPS Chapter 2 Installation Guide Installing the Subscriber Station Make sure the subscriber station is properly grounded according to local standards. For more information, refer to Section 2.7, “Grounding the Subscriber Station”. 10. Tighten the screws connecting the arm bracket to the subscriber station and mounting bracket. Make sure the screws are torqued to 24 N·m (17.7 ft.
Tighten the screws connecting the clamping bracket to the mounting bracket. Make sure the screws are torqued to 14 N·m (10 lbf-ft). Section 2.6 Installing the Antennas The RUGGEDCOM WIN5151-V-GPS supports N-Connect female antennas. To install an antenna, do the following: Installing the Antennas...
Page 19
RUGGEDCOM WIN5151-V-GPS Chapter 2 Installation Guide Installing the Subscriber Station WARNING! Radiation hazard – risk of Radio Frequency (RF) exposure. This subscriber station is compliant with the requirements set forth in FCC CFR 47, section 1.1307, addressing Radio Frequency (RF) exposure...
Section 2.8 Connecting Power and Data The RUGGEDCOM WIN5151-V-GPS requires a 9 to 36 VDC Class 2 power supply. IMPORTANT! When connecting a DC battery power supply, make sure to use a 36 VDC, 3 A, double-pole circuit breaker as the main disconnecting device.
Most outdoor subscriber station, antenna and cable problems are caused by coaxial cable connections loosened by vibration, allowing moisture to penetrate the connector interface. Siemens strongly recommends weatherproofing all outdoor cable connections to prevent the ingress of water and help secure connections.
Chapter 2 RUGGEDCOM WIN5151-V-GPS Installing the Subscriber Station Installation Guide Spray the cable end and connector with SCC3 conformal coating and allow them to dry fully (approximately 3 to 5 minutes depending on the ambient temperature). Apply cold shrink or self-amalgamating tape to the connector end. For information about how to apply these types of seals, refer to Section 2.9.2, “Applying Cold Shrink Tubing”...
RUGGEDCOM WIN5151-V-GPS Chapter 2 Installation Guide Installing the Subscriber Station Section 2.10 Configuring the Subscriber Station Once the subscriber station is installed and connected to the network, it must be configured. The RUGGEDCOM WIN5151-V-GPS features a Web-based User Interface (UI) for all configuration management. For more information about configuring the subscriber station, refer to the RUGGEDCOM WIN Subscriber Station User Guide associated with the subscriber station and the installed software release.
Page 24
Chapter 2 RUGGEDCOM WIN5151-V-GPS Installing the Subscriber Station Installation Guide Configuring the Subscriber Station...
Section 3.3, “Radio and Modem Specifications” • Section 3.4, “Operating Environment” • Section 3.5, “Mechanical Specifications” Section 3.1 Power Supply Requirements The RUGGEDCOM WIN5151-V-GPS requires an external power supply that meets the following requirements: Power Supply Type Class 2 Input Range 10 to 36 VDC Section 3.2 Power Consumption...
Chapter 3 RUGGEDCOM WIN5151-V-GPS Technical Specifications Installation Guide 10 MHz Frequency Resolution 250 kHz Transmission Mode for MIMO MRC/STC (downlink) Antenna Type External RF Number of Ports for External Antenna(s) Type of Ports for External N-Connect female Antenna(s) Maximum Transmit Power 0.5 W...
RUGGEDCOM WIN5151-V-GPS Chapter 5 Installation Guide Certification Certification The RUGGEDCOM WIN5151-V-GPS ODU CPE has been thoroughly tested to guarantee its conformance with recognized standards and has received approval from recognized regulatory agencies. CONTENTS • Section 5.1, “Approvals” • Section 5.2, “Environmental Type Tests”...
Information Technology Equipment – Safety – Part 22: Equipment to be Installed Outdoors The subscriber station is marked with a TÜV Rheinland marking and can be used throughout the European community. A copy of the TÜV Rheinland Declaration of Conformity is available from Siemens Canada Ltd. For contact information, refer to “Contacting Siemens”.
Wireless Access Systems – Amendment for Physical and Medium Access Control Layers for Combined Fixed and Mobile Operation in Licensed Bands Section 5.2 Environmental Type Tests The RUGGEDCOM WIN5151-V-GPS has passed the following environmental tests. Test Description Test Levels IEC 60068-2-1 Low Temperature -25 °C for 72 hours...
Page 32
Chapter 5 RUGGEDCOM WIN5151-V-GPS Certification Installation Guide Test Description Test Levels IEC 60068-2-14 Temperature Change -10 to 45 °C (14 to 113 °F) @ 0.5 °C/min (0.9 °F/min) for 2 cycles -40 to -30 °C (-40 to -22 °F) @ 1 °C/min (1.8 °F/min) for 5 cycles...