Subscribe to Our Youtube Channel
Related Manuals for Timan Comfortably better CS 200
Summary of Contents for Timan Comfortably better CS 200
- Page 1 User Manual CS 200 Comfortably better Applicable to CS 200 types numbers: 725131-00 725133-00 725135-00 725132-00 725134-00 725136-00 725138-00 725140-00 725142-00 www.timan.dk...
-
Page 3: Table Of Contents
INTRODUCTION INTRODUCTION ........................3 ........................... 3 MPORTANT ........................3 MPROPER USE ..................4 DENTIFICATION OF THE MACHINE : ....................5 RDERING PARE ARTS SAFETY RULES ......................... 6 MAINTENANCE AND ADJUSTMENT SAFETY RULES ............7 ... - Page 4 INTRODUCTION SERVICE AND MAINTENANCE OF MACHINE ..............30 14.1 ................31 UBRICATION OF THE OMBI PREADER 14.2 ................. 32 IGHTENING OF ROLLER DRIVE CHAIN 14.3 ................... 32 DJUSTING THE DOSING PLATE 14.4 ..........
-
Page 5: Introduction
INTRODUCTION Congratulations on your new TIMAN Combi Spreader CS 200! These operating instructions will help you to use, adjust and maintain your new machine properly. Before attempting to drive or operate your new machine, please carefully read these operating instructions, especially the section on safety rules. -
Page 6: Dentification Of The Machine
7251xx-00-1001 Type Serial number Batch number 7251xx 1001 Type: CS200 Year: Year of manufacture Weight: The spreader’s dead weight/The spreader’s dead weight with disc spreader Performance: Max. load: Maximum permissible load weight (for Timan tool carrier)/Maximum permissible load weight (other) -
Page 7: Rdering Pare Arts
Having carefully read these user instructions, you will find out that part of the service work can be done by you yourself. But if spare parts and larger service are required, please contact your Timan dealer from whom you purchased the machine or your local authorized Timan service centre. -
Page 8: Safety Rules
SAFETY RULES 2 SAFETY RULES IF THIS SYMBOL IS IN THE MANUAL, YOUR SAFETY IS CONCERNED The user is responsible for the installation of the protective cover and the overall use of the safety equipment and for compliance with the safety rules. Careful driving is the best guarantee for preventing accidents. -
Page 9: Maintenance And Adjustment Safety Rules
Before starting the machine, ensure that all persons are out of its reach and at a distance visible to the operator. Never remove blockages by hand or foot, use a suitable tool instead. It is allowed to use original Timan A/S spare parts only. -
Page 10: Machine Specifications
MACHINE SPECIFICATIONS 4 MACHINE SPECIFICATIONS Technical data. The spreader’s dead weight depends on the type and the equipment installed. The dead weight in the table below is for a standard machine. Model CS 200 CS 200 (with disc spreader) Min. oil flow 20 l/min 20 l/min Max. -
Page 11: Eu Declaration Of Conformity
MACHINE SPECIFICATIONS EU declaration of conformity EC Declaration of Conformity 2006/42/EC Annex II A Manufacturer: Name Timan a/s Address Fabriksvej 13 Post code and city 6980 Tim Compiler of the technical files (authorized by the manufacturer): Name Henning Pedersen Address... -
Page 12: Explanation Of Warning Signs On The Machine
Keep the warning signs clean and if damaged, replace them or add the missing signs immediately. New labels can be ordered from your local Timan dealer. a. WARNING: Read the operating instructions carefully before using the machine. b. WARNING: Before servicing the machine: Stop the machine and remove the key from the tractor. -
Page 13: The Machine's Construction
(only applies to machines with a disc spreader on Timan machines). In the case of tractor models, this function is connected directly from the tractor's remote socket to the cylinder function on the spreader. When using the cylinder function, the disc spreader can be moved between spreading position and roller spreading position. - Page 14 The machine’s construction On machines without a disc spreader, the spreading plate is mounted on two holes at the front at the bottom of the main frame, and can be manually tilted from the spreading position to the transport position.
-
Page 15: Connecting And Disconnecting The Machine
CONNECTING AND DISCONNECTING THE MACHINE 7 CONNECTING AND DISCONNECTING THE MACHINE Timan tool carrier Before connecting, it is important to check that the machine and the vehicle are on a level and stable surface. The connection works as follows, in the following order: Push the tool lifting truck with the combi spreader to the ‐... -
Page 16: Tractor
CONNECTING AND DISCONNECTING THE MACHINE Tractor Before connecting, it is important to check that the machine and the vehicle are on a level and stable surface. The connection works as follows, in the following order: ‐ Back the tractor towards the combi spreader. ‐... -
Page 17: Adjusting The Machine (Roller Spreader)
ADJUSTING THE MACHINE (ROLLER SPREADER) 8 ADJUSTING THE MACHINE (ROLLER SPREADER) The procedure for the following adjustments may vary depending on the equipment mounted on the machine. Material (Split/gravel) IMPORTANT: It is important that the inner sealing plates are removed in the spreader for coarse material such as split/gravel to protect the machine from unnecessary wear and tear. -
Page 18: Adjusting The Bracket For The Bottom Tray
ADJUSTING THE MACHINE (ROLLER SPREADER) Adjusting the bracket for the bottom tray IMPORTANT: It is important that the bracket is lowered for coarse material to avoid unnecessary wear and tear on the machine. The rear bracket for the bottom tray under the roller can be adjusted up and down in height depending on the material being spread. -
Page 19: Speed Of Agitator/Disc Spreader
‐ In the case of machines with electrical control [2] of revolutions, this is adjusted with the switch [5] on the CS-200 control box for Timan 3400, see section (12). The electrically controlled volume divider is adjusted to min. -
Page 20: Setting Doses
In the case of diffusers with electronic dosing, this is controlled using the mounted electric actuator [2]. This is operated using the switch ‐ [5] for Timan 3330 see section (12) ‐ Or the switch [6] on the CS-200 control box for the Timan 3400 Or the switch [3] for CS-200 control box. -
Page 21: Adjusting The Machine (Discspreader)
This is especially true for spreaders mounted on vehicles other than Timan. The most optimal height for the machine is 350 mm ± 50 mm from the lower edge of the spreading discs to the ground surface [1]. -
Page 22: Adjusting Spreading Vanes
ADJUSTING THE MACHINE (DISCSPREADER) Adjusting spreading vanes The spreading vanes can be set to five different positions (middle position [3] is shown in the picture). Adjusting these changes the spreading density of the right and left sides. Adjusting the blades on the left disc changes the spreading density of the left half of the spreading pattern and vice versa for the right side. -
Page 23: Setting The Application Point
ADJUSTING THE MACHINE (DISCSPREADER) Setting the application point If the adjustment of the spreading vanes is insufficient, the application point can be changed for both disc spreaders. This is done as follows: Loosen the three nuts for the disc spreader suspension on both the right and left sides. ‐... -
Page 24: Settings Table
ADJUSTING THE MACHINE (DISCSPREADER) Settings table Your own settings can be recorded in the table below. Materials Position for spreading vanes: Position for application point: [1-5] [1-3]... -
Page 25: Machine Loads
10.1 Timan tool carrier On the Timan tool carrier, the machine and tipper can be loaded with a maximum of 225 kg in total. -
Page 26: Driving By Machine
11.2 Switch between disc spreading and roller spreading ‐ In the case of Timan machines Ensure that switch [4] in section (12) is set to the cylinder function of the combi spreader. When using switch [3] in section (12), the disc unit can be tilted from the active spreading position to passive where the roller distributor works, or vice versa. -
Page 27: Operation Of The Machine
IMPORTANT: When the machine is started, foreign objects may fly out. Therefore, the area around the machine should be secured so that neither animals nor humans are in danger. 12.1 Timan 3330 [1] Starting the machine. [2] Power the machine on/off. -
Page 28: Timan 3400
OPERATION OF THE MACHINE 12.2 Timan 3400 [1] Starting the machine. [2] Power the machine on/off. [3] Cylinder function for tipping loads and tilting disc spreader. [4] Used to switch the work lights on and off at the rear of the spreader (if equipped). -
Page 29: Cs-200 Control Box
OPERATION OF THE MACHINE 12.3 CS-200 control box This control box is used when running the CS-200 on a Timan 3400, Timan Tool-Trac or tractors. The machine is started using the vehicle's hydraulic remote outlet. The disc spreader is tilted using the vehicle's hydraulic remote outlet. -
Page 30: Rotational Test
ROTATIONAL TEST 13 ROTATIONAL TEST To ensure as accurate spreading as possible, it is recommended you perform a rotational test. ‐ Before first spreading ‐ When changing material ‐ If material changes significantly (humidity, size, etc.) 13.1 Dosing manual It is recommended that you run a test for each position at which you want to run with the dosing lever. - Page 31 ROTATIONAL TEST Calculation 2 with: unknown dosage (g/m If the following values are known: ‐ Spreading width (m) ‐ Desired travel speed (km/h) ‐ Output volume (kg/min) - but the dosage (g/m ) is not known and you wish to find it in relation to the outlet quantity and the forward speed, a rotational test is performed and the following calculation is used: Formula for correct traveling speed: Calculation 3 with: unknown forward speed (km/h)
-
Page 32: Service And Maintenance Of Machine
SERVICE AND MAINTENANCE OF MACHINE 14 SERVICE AND MAINTENANCE OF MACHINE IMPORTANT: All service and maintenance on the machine shall only be performed when the following points are complied with: ‐ The vehicle has stopped ‐ The key has been removed from the ignition ‐... -
Page 33: Lubrication Of The Combi Spreader
SERVICE AND MAINTENANCE OF MACHINE 14.1 Lubrication of the Combi Spreader. Proper maintenance is critical for the life of the machine. It is therefore important that the lubrication intervals for bearings, bushings and wheels are observed. The following parts must be lubricated on the combi spreader: ‐... -
Page 34: Tightening Of Roller Drive Chain
SERVICE AND MAINTENANCE OF MACHINE 14.2 Tightening of roller drive chain The chain tension must be checked every 50 hours. IMPORTANT: At the same time, check that the two gear wheels [3] and [4] are running parallel and directly opposite each other. The chain is tightened as follows: ‐... -
Page 35: Adjusting The Hydraulic Cylinder For Disc Spreader
SERVICE AND MAINTENANCE OF MACHINE 14.4 Adjusting the hydraulic cylinder for disc spreader It may be necessary to adjust the position of the hydraulic cylinder to ensure that the disc spreader is in a horizontal position, in the active position [1]. Adjust as follows: ‐... -
Page 36: Quick Emptying Of Containers
SERVICE AND MAINTENANCE OF MACHINE 14.5 Quick emptying of containers To manually empty the machine of material, follow the steps below: ‐ Put the disc spreader in the passive position (see section 11). ‐ Release the two star grips [1]. ‐... -
Page 37: Replacement Of Agitator On Roller
SERVICE AND MAINTENANCE OF MACHINE 14.6 Replacement of agitator on roller IMPORTANT: Before this can be done, the bottom tray must be opened (see section 14.5). The agitators on the roller are wear and tear parts, and must be checked regularly. The agitators are worn out when they can no longer deliver the desired amount, or the feeding is uneven. -
Page 38: Post-Season Maintenance
SERVICE AND MAINTENANCE OF MACHINE 14.7 Post-season maintenance. After the season, it is important to wash the machine thoroughly (hole for washing behind the limitation plate [1]), and to lubricate all bearings, bushings and the chain to push any water out. After lubrication, it is important that the bushings and bearings are rotated to distribute the grease over the entire surface. -
Page 39: Machine Warranty Terms
For the purposes of the payment of the costs incurred in connection with complaints, it is necessary to prepare a complaint report and send it to Timan not later than within 14 days from the date when the damage was incurred. - Page 40 MACHINE WARRANTY TERMS The guarantee period for spare parts and repairs is three months. However, this guarantee period applies only until the end of the original guarantee period for the relevant delivery. If unauthorized modifications or repairs are carried out by the customer or a third party without prior agreement with the supplier, the liability for any damage caused by such modifications or repairs ceases to exist.
-
Page 41: Using The Machine - Qr Code
The features of the machine are described with videos which you can access by scanning the QR code with your mobile phone or tablet. It is important that you are familiar with the machine before you start driving. 16.1 Timan 3400 (Applicable to type numbers: 725131, 725132 and 725138) The video material contains the following points: ‐... -
Page 42: Timan 3330
USING THE MACHINE - QR CODE 16.2 Timan 3330 (Applicable to type numbers: 725131, 725132 and 725138) The video material contains the following points: The structure of the machine ‐ 1. The structure of the machine Switching the machine on and off ‐... -
Page 43: Timan 5740 Tool-Trac
USING THE MACHINE - QR CODE 16.3 Timan 5740 Tool-Trac (Applicable to type numbers: 725133, 725134 and 725140) The video material contains the following points: The structure of the machine ‐ 1. The structure of the machine Switching the machine on and off ‐... -
Page 44: Tractor/Other
USING THE MACHINE - QR CODE 16.4 Tractor/other (Applicable to type numbers: 725135, 725136 and 725142) The video material contains the following points: The structure of the machine ‐ 1. The structure of the machine Switching the machine on and off ‐... -
Page 45: Hydraulics And Electrical Diagrams
HYDRAULICS AND ELECTRICAL DIAGRAMS 17 HYDRAULICS AND ELECTRICAL DIAGRAMS... - Page 46 Draw. date: Creator.: Ctrl.: 210120 PROPERTY AND CONFIDENTIALITY THE INFORMATION CONTAINED ON THIS Page: PAGE BELONGS SOLELY TO TIMAN A / S. Rev. date: Creator.: Ctrl.: Fabriksvej 13, hal 1, DK-6980 Tim REPRODUCTION IN PART OR COPY WITHOUT WRITTEN APPROVAL FROM Tel: +45 97 330 360 TIMAN A / S IS PROHIBITED.
- Page 50 Draw. date: Creator.: Ctrl.: 090620 PROPERTY AND CONFIDENTIALITY THE INFORMATION CONTAINED ON THIS Page: PAGE BELONGS SOLELY TO TIMAN A / S. Rev. date: Creator.: Ctrl.: Fabriksvej 13, hal 1, DK-6980 Tim REPRODUCTION IN PART OR COPY WITHOUT WRITTEN APPROVAL FROM Tel: +45 97 330 360 TIMAN A / S IS PROHIBITED.
- Page 51 Draw. date: Creator.: Ctrl.: 121020 PROPERTY AND CONFIDENTIALITY THE INFORMATION CONTAINED ON THIS Page: PAGE BELONGS SOLELY TO TIMAN A / S. Rev. date: Creator.: Ctrl.: Fabriksvej 13, hal 1, DK-6980 Tim REPRODUCTION IN PART OR COPY WITHOUT WRITTEN APPROVAL FROM Tel: +45 97 330 360 TIMAN A / S IS PROHIBITED.
Need help?
Do you have a question about the Comfortably better CS 200 and is the answer not in the manual?
Questions and answers