Advertisement
Available languages
Available languages
VENTILACIÓN EXTERIOR TRASERA
C
VISIÓN GENERAL DE LA
INSTALACIÓN
C1. Prepare la Pared Trasera
C2. Adjunte la Placa de Montaje
a la Pared
C3. Prepare el Gabinete Superior
C4. Ajuste el Calentador
C5. Monte el Horno Microondas
PREPARACIÓN DE LA PARED
C1
TRASERA PARA EL ESCAPE
EXTERNO TRASERO
Es necesario cortar una abertura en la pared trasera
del escape externo.
• Lea las instrucciones sobre la PLANTILLA DE LA
PARED TRASERA.
• Pegue la misma a la pared trasera, alineándola
con los agujeros previamente perforados A y B
en la placa de montaje.
• Corte la apertura, siguiendo las instrucciones de
la PLANTILLA DE LA PARED TRASERA.
20
Instrucciones de Instalación
3/8" TO EDGE
OPTION 2
OPTION 1
12"
mark is made by using the stampled slot in bracket.
STEP 1:
Installer uses bracket to make 2 marks. First
Second mark is made on the ouside edge of bracket.
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
F. CUT OUT FOR HORIZONTAL
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
4"
OUTSIDE EXHAUST
Horizontal line
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
1. Use a level to check that the template is positioned
accurately.
here,
Make a mark
Make a mark here, along
inside bottom of the
STEP 4:
2. Locate and mark at least one stud on the left or
bottom of
even with
stamped
stamped slot provided.
right side of the centerline.
slot
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
STEP 2:
the cabinets and makes 2 more marks. Marks are the
Installer moves bracket to the other side of
locations for the supplied toggle bolts.
same as STEP 1, just opposite side.
3. Drill holes in the marked locations. Where there is
that do not line up with a stud, drill 5/8" holes for
a stud, drill a 3/16" hole for wood screws. For holes
toggle bolts.
NOTE::
D O NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
5. Review the Installation Instruction book for your
4. Remove the template from the rear wall.
installation situation.
Make a
inside bottom of the
Make a mark here, along
even with
mark here,
Darle vuelta a la hoja para consultar la
(same as Step 1).
stamped slot provided
stamped
bottom of
slot
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
NOTES:
30" MINIMUM WIDTH REQUIRED
- 13" Max Cabinet Depth
Locate and mark holes to align with holes in the
- 15" deep cabinets require additional steps using
mounting plate.
an additional installation kit: JX36BUMP
IMPORTANT:
REAR WALL TEMPLATE
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Trim the rear wall template along the dotted line.
A
C
D
B
ADHIERA LA PLACA DE
C2
MONTAJE A LA PARED
Adhiera la placa a la pared usando tornillos con
resortes. Por lo menos un tornillo de madera deberá
ser usado para adherir la placa al montaje de pared.
1
Retire las tuercas mariposa de los tornillos.
Inserte los tornillos en la placa de montaje a través
2
de los agujeros designados para entrar en la placa
de yeso y vuelva a ajustar las tuercas mariposa a
3/4" sobre cada tornillo.
Para usar tornillos con resorte:
Espacio para Tornillos con Resorte
Superior al Grosor de la Pared
Tuercas Mariposa
Placa de
Tornillo con
Montaje
Resorte
Pared
Coloque la placa de montaje contra la pared e
3
inserte las tuercas mariposa en los agujeros de la
pared para montar la placa
PRECAUCIÓN
pellizcos en los dedos entre la parte trasera de la
placa de montaje y la pared.
4
Ajuste todos los tornillos. Empuje la placa hacia
afuera de la pared para ayudar a ajustar los tornillos.
(Conducto Horizontal)
Extremo del Tornillo
Tenga cuidado para evitar
31-7000092 Rev. 2
Advertisement
