Advertisement
Available languages
Available languages
RECIRCULATING
A
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Check Blower Orientation
A4. Adapting Microwave Blower For Recirculation
A5. Mount the Oven
A6. Installing The Charcoal Filter
A1
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts and
wood screws. At least one wood screw must be
used to attach the plate to a wall stud.
1
Remove the toggle wings from the bolts.
2
Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to
To use toggle bolts:
Spacing for Toggles More
Than Wall Thickness
Toggle Wings
Mounting
Toggle
Plate
Bolt
Wall
12
Installation Instructions
(Non-Vented Ductless)
3 4
Bolt End
3/8" TO EDGE
OPTION 2
12"
STEP 1:
Installer uses bracket to make 2 marks. First
OPTION 1
Second mark is made on the ouside edge of bracket.
mark is made by using the stampled slot in bracket.
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
F. CUT OUT FOR HORIZONTAL
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
4"
OUTSIDE EXHAUST
Horizontal line
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
1. Use a level to check that the template is positioned
outlet.
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
accurately.
here,
Make a mark
Make a mark here, along
inside bottom of the
STEP 4:
2. Locate and mark at least one stud on the left or
bottom of
even with
stamped slot provided.
right side of the centerline.
stamped
slot
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
STEP 2:
Installer moves bracket to the other side of
of the microwave. Mark two additional, evenly spaced
the cabinets and makes 2 more marks. Marks are the
locations for the supplied toggle bolts.
same as STEP 1, just opposite side.
3. Drill holes in the marked locations. Where there is
that do not line up with a stud, drill 5/8" holes for
a stud, drill a 3/16" hole for wood screws. For holes
toggle bolts.
NOTE::
D O NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Make a
Make a mark here, along
mark here,
even with
Darle vuelta a la hoja para consultar la
stamped slot provided
(same as Step 1).
inside bottom of the
bottom of
stamped
versión en Español.
slot
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
NOTES:
- 13" Max Cabinet Depth
30" MINIMUM WIDTH REQUIRED
Locate and mark holes to align with holes in the
- 15" deep cabinets require additional steps using
mounting plate.
an additional installation kit: JX36BUMP
IMPORTANT:
REAR WALL TEMPLATE
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Trim the rear wall template along the dotted line.
A
C
D
B
IMPORTANT: Do NOT
remove the cardboard spacers
between the heat shield and
door
3
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall to
mount the plate.
CAUTION
Be careful to avoid pinching
fingers between the back of the mounting plate
and the wall.
Tighten all bolts. Pull the plate away from the wall
4
to help tighten the bolts.
A2
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
Wear safety goggles when drilling
CAUTION
holes in the cabinet bottom.
31-7000092 Rev. 2
Advertisement
