Amax VA-2080 - ULTRA COMPACT FOLDING MICRO DRONE Manual
![]()
PACKAGE CONTAINS
![]()
Colors and styles may vary slightly.
FEATURES
- Air Pressure Sensor Locks Flight Altitude
- Built In 6 Axis Gyroscopic Chip Keeps the VA-2080 Extremely Stable in All Conditions
- Automatically Starts and Lands
- Different Speed Settings for Slow to High Speed Flying
- Head Light
REMOTE CONTROL BATTERY INSTALLATION
- Unscrew and remove the battery cover from the back of the remote control as shown in diagram A.
![Amax - VA-2080 - REMOTE CONTROL BATTERY INSTALLATION - Step 1 REMOTE CONTROL BATTERY INSTALLATION - Step 1]()
- Install 2"AAA" alkaline batteries into the battery compartment as shown in the diagram A1.
![Amax - VA-2080 - REMOTE CONTROL BATTERY INSTALLATION - Step 2 REMOTE CONTROL BATTERY INSTALLATION - Step 2]()
- Replace the battery cover and secure it.
CHARGING YOUR VA-2080 BATTERY
- Turn the VA-2080 Off. Plug the charging cable into the VA-2080 charging socket.(see diagram B).
![]()
B - Connect the USB end of the cable to your computers USB port or a USB wall charger (see diagram B1).
![]()
B1
The red LED on the USB plug lights up when charging is complete.
Note: If the red LED lights up, either the charging is complete or the USB plug is not properly connected. - Average charging time is approximately 40 minutes ( via 5.0V
2A USB wall charger). The VA-2080 operates for approximately 5-6 minutes on full charge.
Note: Periodically examine the charger for external damage. External damage to the charger may result in the risk of fire, electric shock, or injury to persons. Never use a damaged adapter.
![]()
ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!
HOW TO EXPAND AND FOLD YOUR VA-2080
Before flying your VA-2080, you need to expand the foldable arms out. Turn your VA-2080 over, bottom side facing you, pull and expand the 4 arms as shown in the diagram below carefully. Make sure the arms are fully expanded to the position with a click sound. After flying your VA-2080, it is recommended to fold all 4 arms back in. When expanding or folding your VA-2080, make sure to be gentle.(see diagram C)
![Amax - VA-2080 - HOW TO EXPAND AND FOLD YOUR VA-2080 HOW TO EXPAND AND FOLD YOUR VA-2080]()
VA-2080 DIAGRAM
![Amax - VA-2080 - VA-2080 DIAGRAM VA-2080 DIAGRAM]()
REMOTE DIAGRAM
![Amax - VA-2080 - REMOTE DIAGRAM REMOTE DIAGRAM]()
![]()
DO NOT FLY YOUR VA-2080 IN FOUL WEATHER!
![Amax - VA-2080 - DO NOT FLY YOUR VA-2080 IN FOUL WEATHER! DO NOT FLY YOUR VA-2080 IN FOUL WEATHER!]()
PREPARING FOR FLIGHT
- Verify that there are 2"AAA"batteries inside the remote control unit and the VA-2080 has been fully charged.
- Make sure to be in a large space with an open radius of at least 50 feet.
- Make sure the empty space has no obstacles or rivers. Set your VA-2080 on a clean flat surface before take-off.
DO NOT ATTEMPT TO FLY YOUR VA-2080 IF THERE IS RAIN, SNOW, HEAVY WINDS,THUNDER OR LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR PRODUCT.
SYNCING YOUR VA-2080
![]()
When syncing your VA-2080 quadrocopter with the controller always make sure that the quadrocopter is on a flat level surface and that your digital trim settings are in the center position. This ensures that the 6 Axis gyro is properly programmed to mimic your trim settings. Your VA-2080 utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless range with no interference.
For One-Person Play:
- Before starting, make sure that the power on both your controller and VA-2080 are in the OFF position. Make sure that there are no other 2.4G devices in the area as well.
- Press On/0ff switch and hold for 2 seconds turn ON the VA-2080 and set it down on a flat surface. The LED indicator lights of the VA-2080 should begin to flash rapidly.
- Turn ON the remote, you will hear two short beeps. The VA-2080's LED lights flash rapidly. Push the throttle on the left all the way forward(l beep) and then pull the throttle all the way back. A 2nd beep will sound and the VA-2080's lights should turn to solid. This indicates your controller and the quadrocopter are successfully synced. If not, repeat above steps.
For Multi Person Play:
- Before starting, make sure that the power on all VA-2080 drones and Controllers are in the OFF position. Make sure that there are no other 2.4 G devices in the area.
- Each person will have to sync their VA-2080 individually at a different time to avoid interference. Follow steps 1 to 3 above making sure that no one else is syncing at the same time.
- After syncing a player's VA-2080, it should be left ON until all players have synced their VA-2080 quadrocopters.
- Should there be a mistake or interference, all players must turn off their controllers and VA-2080 quadrocopters for up to 60 seconds and then begin the process again.
FLYING TIPS
- It is recommended that you operate the VA-2080 in a wide space. The ideal space should have a 61 m/200 ft radius.
- Parental guidance or adult supervision is suggested at all times.
- If you are flying the VA-2080 with others, make sure all spectators are behind you.
- For best performance, it is recommended that you operate the VA-2080 in zero wind conditions. Wind can greatly affect the performance of the VA-2080.
NOW YOU ARE READY TO FLY!
If you have successfully synced your VA-2080 to your controller as explained you are now ready to fly. Before beginning to fly your drone you should familiarize yourself with how to start and stop the rotors, how to use your take off and auto land feature and how the controls work. Please carefully read and familiarize yourself with various control features explained in the next few pages. Once again as a beginner pilot you should learn how to control your drone in a large open field or park on a day with zero or very light wind. Do not try to fly your VA-2080 too high until you become a more experienced pilot.
RECOGNIZING THE FRONT AND REAR OF THE VA-2080
![]()
Even though the VA-2080 has four rotors there is still a front or forward-facing Front direction and back or backwards-facing direction. The Front and forward-facing direction of the VA-2080 is the side with white color head light. The rear and back of the VA-2080 is where the power ON/OFF is. The VA-2080 when in flight will also help you keep aware of the orientation with lighted LED lights in the arms of the VA-2080.
NOTE: The front of the VA-2080 displays WHITE LED lights and the back of the VA-2080 displays RED LED lights.
AUTOMATICALLY TAKE OFF / LAND
Make sure you have properly synced The VA-2080.
- simply press the Auto Start/Land button, your VA-2080 will automatically take off.
- To stop or land the VA-2080 just Press the Auto Start/Land button again and the VA-2080 will descend and land automatically (see diagram D).
![]()
D
Tips:You also can move the two control sticks simultaneously down inside or outside corners, hold them till you hear a"beep"and the blades start spinning. Release the control sticks and push the throttle stick slowly to take off manually (see diagram D1).
![]()
D1
UNDERSTANDING THE ALTITUDE LOCK
The VA-2080 has a unique Altitude Lock function. With the help of air pressure sensor you can control, your VA-2080 more stable than ever. The sensor locks in the altitude of the drone while allowing the user to adjust the directional control without having to hold the throttle.
After starting the Drone, fly upwards to a safe height. Once at a safe height, let go of the throttle control, your VA-2080 should lock in the altitude and allow the user to focus on getting used to the directional controls.
NOTE: The altitude sensor does have some tolerance based on atmospheric conditions and could have a slight variation in altitude.
The VA-2080 has 3 speed settings; 1(SLOW), 2(MEDIUM) and 3(HIGH).The Default setting when you first turn on your VA-2080 is 1(SLOW).To change speed, just press and release the speed setting button (see remote diagram). Speed level is indicated by number of beeping sounds, one beeping sound for slow speed, two for medium speed and three for high speed.
T (Training) MODE
Simply press and hold the Speed Button, you will hear a long beep indicating you are in T Mode now. T mode allows you to learn how to operate your VA-2080 at a very slow speed. Also there are maximum and minim height limits set to avoid crashing to ceiling or floor in T mode. To exit T mode just press the speed setting button again.
UNDERSTANDING TRIM ADJUSTMENTS
Forward/Backward Trim
- If your VA-2080 is moving forwards or backwards automatically, you may need to adjust the FORWARD/BACKWARD TRIM buttons.
- If your VA-2080 flies forward, push and release the Backward TRIM button repeatedly until the moving stops and proper flight is maintained.
- If your VA-2080 flies backwards, push and release the Forward TRIM button in the same manner until the problem is resolved.
- From time to time you may have to adjust the FORWARD/BACKWARD TRIM to ensure the VA-2080 will hover in mid-air and respond accurately to your commands.
Forward/Backward Trim Controls
![]()
Push backward trim button
![]()
Push forward trim button
![]()
Banking Left/Right Trim
- If your VA-2080 is not steadily hovering and is banking to the left or right automatically, you may need to adjust the BANKING TRIM buttons.
- If your VA-2080 banks to the left, push and release the R Trim button repeatedly until the banking stops and proper flight is maintained.
- If your VA-2080 banks to the right, push and release the L Trim button in the same manner until the problem is resolved.
- From time to time you may have to adjust the BANKING TRIM to ensure the VA-2080 will and respond accurately to your commands.
Left/Right Banking Controls
![]()
Push the " L " trim button to increase left banking sensitivity
![]()
Push the " R " trim button to increase Right banking sensitivity
![]()
NOTE: The use of the Trim buttons are accompanied with a beep tone. A single long beep indicates the product is centre-trimmed. No beeping after press the trim button indicates the product is trimmed to the maximum on a particular side.
FLIGHT CONTROL
Move the Throttle up to increase the speed of the motors and the VA-2080 will rise up.
![]()
Move the Throttle down to decrease the speed of the motors and the VA-2080 will descend.
![]()
Move the Throttle stick left and the VA-2080 will rotate left.
![]()
Move the Throttle stick right and the VA-2080 will rotate right.
![]()
Move the Direction Control up and the VA-2080 will move forward.
![]()
Move the Direction Control down and the VA-2080 will move backward.
![]()
Move the Direction Control left and the VA-2080 will bank to the left.
![]()
Move the Direction Control right and the VA-2080 will bank to the right.
![]()
CALIBRATING THE VA-2080
If the VA-2080 becomes unstable during the course of flying, you may need to calibrate the internal gyros. To do this place the VA-2080 on a flat level surface. Do not start the blades. Instead move both the throttle and control stick down and to the right corner. The LEDs on the VA-2080 will flash quickly and then remain solid. This indicates your drone has been recalibrated (see diagram E).
![]()
E
HOW TO DO 360o STUNT ROLLS
- In order to make your VA-2080 do 3600 rolls you must fully charge your battery.
Note:The VA-2080 will not do 3600 stunt rolls under low battery indication. - Once you are ready to attempt a 3600 roll, simply depress and let go of the "STUNT" button on the top right hand side of your controller (see Remote Diagram).
You will hear beeping sounds, this means you are now in "STUNT MODE." - Now quickly move your right control stick in any of 4 directions; up, down, left or right. Your VA-2080 drone will instantly roll in the associated direction. See diagram below.
![Amax - VA-2080 - HOW TO DO 360o STUNT ROLLS HOW TO DO 360o STUNT ROLLS]()
Note: After performed the stunt roll, the beeping sounds will stop. Repeat step 2 to 3 ifyou wish to do it again.
CARE AND MAINTENANCE
- Always remove the batteries from the wireless remote control when it is not being used for an extended period of time.
- To clean, gently wipe the remote control and VA-2080 with a clean damp cloth.
- Keep the toy away from direct heat or sunlight.
- Do not submerge the toy into water. This can damage the unit beyond repair.
- Parental guidance recommended when installing or replacing the batteries.
REPLACING THE PROPELLER BLADE
Your VA-2080 propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your VA-2080's propellers.
- VA-2080 have four blades, Please note that the four blades of the VA-2080 are labeled with an embossed A or B (see the diagram F).
![]()
F
- When replacing the propeller blades, gently remove the blade from the rotor shaft. Make sure to match the indication letter on the blade with the letter on the aircraft.
- Replace the broken blade with the correct spare blade.
Blade Front Left = A
Blade Front Right = B
-----------------------------------------
Blade Rear Left = B
Blade Rear Right = A
VA-2080 WARNING
![]()
Never leave product charging unattended for extended periods of time. Always disconnect VA-2080 from charger immediately after the VA-2080 i s fully charged. Please refer to enclosed safety instructions.
The VA-2080 is designed for INDOOR and OUTDOOR use. The VA-2080 blades revolve at high speeds and can cause damage to the user, spectators and animals. Stand away from the VA-2080 to reduce the risk of getting into the flight path. Warn spectators that you will be flying your VA-2080 so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the VA-2080.
![]()
- Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.
- Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the ON position.
- Turn off the transmitter and VA-2080 power switches when not in use.
- The included charger is built specifically for the VA-2080 Li-Poly battery. Do not use it to charge any other battery.
- New alkaline batteries are recommended for maximum performance.
- Parental supervision recommended when flying VA-2080.
BATTERY WARNINGS
RECHARGEABLE BATTERY
This VA-2080 uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery properly according to local disposal requirements.
CONTROLLER BATTERIES
Remote control requires 2 "AAA" batteries (not included). Please read the important battery safety warning below.
- Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (nickel metal hydride).
- Do not mix old and new batteries.
- Non-rechargeable batteries are not to be recharged.
- Rechargeable batteries are to be removed from the item before being charged (if removable).
- Rechargeable batteries are only to be charged under adult supervision.
- Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations.
- The supply terminals are not to be short-circuited.
- Only batteries of the same or equivalent type as recommended are to be used.
- Batteries are to be inserted with the correct polarity (see inside booklet for diagram).
- Do not dispose of batteries in a fire - batteries may leak or explode.
Email: customercare@amaxbrands.com
www.amaxbrands.com
![]()
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Amax VA-2080 - ULTRA COMPACT FOLDING MICRO DRONE Manual
Need help?
Do you have a question about the VA-2080 and is the answer not in the manual?
Questions and answers