Table of Contents
Advertisement
FCC Part 15 C Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC RF exposure statements
This Transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body or nearby persons.
WARNING!
Requires Speed Class 10 or higher microSD or
CHOKING HAZARD - Small parts.
microSDHC card(not included)
Not suitable for children under 3 years.
microSDHC Logo is a trademark of SD-3C, LLC.
Conforms to safety requirements of FCC.
Ascend Aeronautics™ is the registered trademark of AMAX Industrial Group LTD.
AMAX Group USA Address: 12645 Memorial Dr Suite F1 #388 Houston, TX 77024
© 2021 All Rights Reserved. Visit us at www.amaxbrands.com
17
Distributed by:
WARNING: Never leave your drone charging unattended for extended periods of
TRACTOR SUPPLY COMPANY
5401 VIRGINIA WAY
BRENTWOOD, TN 37027
For customer support,
call: 1-888-376-9601
www.TractorSupply.com
ASC-2080
Made in China
C012-USA-V 1.0
ASC-2080
COMPACT HD VIDEO DRONE
WITH WIDE ANGLE LENSE
INSTRUCTION BOOKLET
time. Always disconnect the battery from charger immediately after the battery
is fully charged. Please refer to the enclosed safety instructions.
PACKAGE CONTAINS:
2.4G Wireless
USB Charger
Spare Parts
Controller
Colors and styles may vary slightly from photos
ON BOARD
ON BOARD
HD CAMERA
HD VIDEO
1280 x 720 pixels
25 frames per second
Phone Holder
Battery
Instruction
Manual
Advertisement
Table of Contents
Related Manuals for Amax ASC-2080
Summary of Contents for Amax ASC-2080
- Page 1 Conforms to safety requirements of FCC. Ascend Aeronautics™ is the registered trademark of AMAX Industrial Group LTD. AMAX Group USA Address: 12645 Memorial Dr Suite F1 #388 Houston, TX 77024 © 2021 All Rights Reserved. Visit us at www.amaxbrands.com ASC-2080 2.4G Wireless...
-
Page 2: Table Of Contents
How to Expand and Fold Your ASC-2080 Arms ....... 2... -
Page 3: Asc-2080 Diagram
ASC-2080. 2. Insert the battery into the ASC-2080 and set it down on a flat level surface. Press down the power button and hold for a few seconds (see diagram F).The LED lights on the drone should begin to flash. -
Page 4: Now You Are Ready To Fly
If you have successfully synced your ASC-2080 to your controller as explained on page 4 you are now ready to learning to fly your ASC-2080 it is best to start in a large space with the drone facing away from you until fly. -
Page 5: Adjusting The Trim
1. Place the ASC-2080 on a flat level surface 2. Make sure the ASC-2080 is on and that the controller is synced (refer to syncing pg 4). Do not start the blades. Instead move both the throttles and control stick down and to the right corner (see diagram R). -
Page 6: Recording Videos And Taking Photos With Your Asc-2080 Drone
“click” into the SD card slot. • Turn the ASC-2080 on and make sure that it is both fully charged and properly synced to the controller (See “HOW TO SYNC YOUR ASC-2080” on page 4 ). -
Page 7: Camera Video And Photo Streaming Setup
3. Batteries may be low or in need of charging correctly (see diagram A) 3. To Download the ASC-2080 App, scan the appropriate Q R code below which will link to the App on either 3. Replace batteries the Android Play Store or Apple Store. If you are not able to scan the Q R code, manually enter the web address located under the appropriate Q R code for your phone. -
Page 8: Replacing The Propeller Blades
Before flight, inspect the rotor blades to make certain that the blades are securely fastened 1. The ASC-2080 has four sets blades, two sets blades with indication number A & B on front, and two to the ASC-2080. -
Page 9: Limited 90-Day Warranty
ALONG WITH THE ORIGINAL RECEIPT evidencing that the product was purchased from an approved AMAX retail partner and that the product is still within the 90 day warranty period. The warranty covers normal consumer use and does not cover damage...
Need help?
Do you have a question about the ASC-2080 and is the answer not in the manual?
Questions and answers