Table of Contents
Advertisement
FCC Part 15 C Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC RF exposure statements （for the drone only）
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body or nearby persons.
Conforms to safety requirements of FCC.
Ascend Aeronautics™ is the registered trademark of AMAX Industrial Group LTD.
AMAX Group USA Address: 12645 Memorial Dr Suite F1 #388 Houston, TX 77024
© 2021 All Rights Reserved. visit us at www.amaxbrands.com
Distributed by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA 98124-1535
USA
1-800-774-2678
www.costco.com
15
WARNING: Never leave your drone charging unattended for extended periods of
time. Always disconnect the battery from charger immediately after the battery
is fully charged. Please refer to the enclosed safety instructions.
WARNING!
CHOKING HAZARD - Small parts.
Not suitable for children under 3 years.
ASC-2400
2.4G Wireless
Made in China
CT-6333
C009-USA-V1.0
ASC-2400
HD VIDEO DRONE
INSTRUCTION BOOKLET
PACKAGE CONTAINS:
Spare Parts
USB Charger
Phone Holder
Controller
Colors and styles may vary slightly from photos
ON BOARD
ON BOARD
HD CAMERA
HD VIDEO
1280 x 720 pixels
25 frames per second
Battery
Set of 4 AAA
Instruction
Batteries
Manual
for Controller
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Amax ASC-2400
Summary of Contents for Amax ASC-2400
- Page 1 Please refer to the enclosed safety instructions. Ascend Aeronautics™ is the registered trademark of AMAX Industrial Group LTD. AMAX Group USA Address: 12645 Memorial Dr Suite F1 #388 Houston, TX 77024 PACKAGE CONTAINS: © 2021 All Rights Reserved. visit us at www.amaxbrands.com...
- Page 2 Installing The ASC-2400 Battery ......... . . 2 How To Expand And Fold Your ASC-2400 Arms ......2 REMOTE CONTROL BATTERY INSTALLATION ASC-2400 Diagram .
- Page 3 ASC-2400. 2. Insert the battery into the ASC-2400 and set it down on a flat level surface. Press down the power button and hold for a few seconds (see diagram G). The red LED lights on the drone should begin to flash rapidly first and then flash slow.
- Page 4 The ASC-2400 has an auto start/auto land feature which allows you to start and land automatically. Simply press the auto START/LAND button on the face of the controller (see diagram I) and your ASC-2400 will begin taking off or land (if your already in the air).
- Page 5 1. Place the ASC-2400 on a very flat level surface. 2. Make sure the ASC-2400 is turned on and that the controller is synced (refer to syncing pg 4). Do not start Forward/Backward Trim the blades! Instead move both the throttle and control stick down and to the right hand bottom corner •...
- Page 6 QR code for your phone. 4. After the ASC-2400 App is installed, it should create an icon on your screen (see icon below). Click the icon to run the App and make sure that it has installed correctly on your device. If not, please delete and repeat the process again.
- Page 7 POSSIBLE SOLUTION 1. Power switched off 1. Press the ON/OFF switch to ON 1. The ASC-2400 has four sets blades, two sets of blades with indication letters A & B on front, and two sets No Power 2. Polarity is reversed 2.
- Page 8 Stand away from the ASC-2400 to reduce the risk of Limited 90-Day Warranty getting into the flight path. Warn spectators that you will be flying your ASC-2400 so that they are aware NORTH AMERICA of its position.
Need help?
Do you have a question about the ASC-2400 and is the answer not in the manual?
Questions and answers