Page 1
Manufactured by Harvard Medical Devices Ltd. HK Share Info Consultant Service LLC Repräsentanzbüro Made in China Heerdter Lohweg 83, 40549 Düsseldorf Harvard Medical Devices Ltd. HK 1002, Railway Plaza, TST, HK Blood Pressure Monitor Instruction Manual WBP1 0197 Kinetik WBP1 EN IB 20221117...
General Description Our manual should provide you with all the information you need Thank you for selecting Kinetik arm type blood pressure monitor (WBP1). The monitor features blood pressure measurement, pulse rate measurement to set up and use this product.
INTRODUCTION INTRODUCTION CAUTION Safety Information * Do not take any therapeutic measures on the basis of a self measurement. Never alter the dose of a The signs below might be in the user manual, labeling or other component. medicine prescribed by a doctor. Consult your doctor if you have any question about your blood pressure. They are the requirement of standard and using.
INTRODUCTION INTRODUCTION CAUTION LCD display signal * If you experience discomfort during a measurement, such as pain in the arm or other complaints, press the START/STOP button to release the air immediately from the cuff. Loosen the cuff and remove it from your arm.
List The display is dim The display does not light up. 1. Blood Pressure Monitor 2. Cuff (Type BF applied part) (WBP1) (22cm~42cm) (Please use Kinetik CAUTION authorized cuff. The size of the actual cuff please Do not use new and used batteries together.
BEFORE YOU START BEFORE YOU START 3. Press “ ” button to confirm [YEAR]. Then the monitor Setting Date and Time. diverts to [MONTH] and [DAY] setting. It is important to set the clock before using your blood pressure mmHg monitor, so that a time stamp can be assigned to each reading that is stored in the memory.
BEFORE YOU START TAKING A MEASUREMENT 5. Repeat steps 2 and 3 to set the [HOUR] and [MINUTE]. Fitting the cuff mmHg mmHg 1. Remove all Jewellery, such as watches and bracelets from your left arm. Note: If your doctor has diagnosed you with poor circulation in your left arm, use your right arm.
TAKING A MEASUREMENT DATA MANAGEMENT Start the Measurement Check the memory When the monitor is off, press “ ” button to turn on the 1. When the monitor is off, please press “ ” button to show the monitor, and it will finish the whole measurement. average value of the latest three records.If the records are less than 3 groups, it will display the latest record instead.
DATA MANAGEMENT INFORMATION FOR USER Delete the Readings Tips for Measurement If you did not get the correct measurement, you can delete all Measurements may be inaccurate if taken in the following results for the selected user by following steps below. circumstances.
ABOUT BLOOD PRESSURE ABOUT BLOOD PRESSURE What are systolic pressure and diastolic pressure? Why does my blood pressure Systolic Diastolic When ventricles contract and pump blood out of fluctuate throughout the day? the heart, the blood pressure reaches its maximum blood entering blood discharging vein...
TROUBLE SHOOTING SPECIFICATIONS This section includes a list of error messages and frequently Battery powered mode: Power supply 6VDC 4×AAA batteries asked questions for problems you may encounter with your blood pressure monitor. If the product is not operating as you think it Display mode Digital LCD display V.A.65mm×50mm should, check here before arranging for servicing.
MANUFACTURER INFORMATION COMPLIED STANDARDS LIST AND EMC GUIDANCE Manufacturer Information Complied Standards List Manufactured by: Harvard Medical Devices Ltd. HK Company: Harvard Medical Devices Ltd. HK EN ISO 14971:2012 / ISO 14971:2007 Medical devices - Risk management Address: 1002, Railway Plaza, TST, HK Application of risk management to medical devices EN ISO 15223-1:2016 / ISO 15223-1:2016 Medical devices.
Warning: Portable RF communications equipment (including peripherals such as antenna IEC 61000-4-4 cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the equipment WBP1, including cables specified by the manufacturer. Otherwise, Surge Not application Not application degradation of the performance of this equipment could result.
Page 15
COMPLIED STANDARDS LIST AND EMC GUIDANCE Table 3 Guidance and manufacturer’s declaration - electromagnetic Immunity Test Band Service Modulation Modulation Distance (m) IMMUNITY Radiated RF Frequency (MHz) TEST IEC61000-4-3 (MHz) LEVEL (Test (V/m) specifications 380- TETRA Pulse ENCLOSURE modulation b) PORT 18Hz IMMUNITY to...
Need help?
Do you have a question about the WBP1 and is the answer not in the manual?
Questions and answers