Scanning The Rx Frequencies - JRC JSS-2150N Instruction Manual

Mf/hf radio equipment
Hide thumbs Also See for JSS-2150N:
Table of Contents

Advertisement

4.3.9

Scanning the Rx frequencies

( 1 )
Scanning of channels in TEL/DSC/CW mode
The scanning of channels in the TEL/DSC/CW mode is started with the controller.
Procedure
1 1
. .
1
.
Press the
MENU
hierarchical menus, after 5.4 Receiver
appears, move the cursor to 7. Scan.
2 2
. .
2
.
Press ENT to confirm the selection.
The group list as shown at right is displayed.
-
The previous scan can be restarted
Note
by pressing and holding the
key and then pressing the
2
SCAN
-
If the user channel is not registered,
scan cannot be done so the screen
shown at right is not displayed. (See
5.4 for user channel registration.)
3 3
. .
3
.
Select the channel group to scan with the
cursor and press ENT.
The popup screen as shown at right is
displayed.
If the popup screen shown at right
Note
is displayed during scanning, Stop
appears instead of Execute.
4 4
. .
4
.
Select 1. Execute and press ENT, the screen
at right is displayed and scanning starts.
 To check the registered channels in the
channel group, select 2. User channel list
and press ENT.
 To change the scanning speed, select 3.
Scan speed (sec) and press ENT. The setting
range is 0.3 to 9.9 seconds, the same as
TEL/DSC/CW.
-
Scanning can be done regardless of the squelch being set to open or close.
Note
When pressing the PTT or keying the CW keyer, or when squelch is opened
after closing condition, scanning stops momentarily and the icon starts
blinking. In this case the scanning can be restarted by pressing ENT.
-
To stop scanning, press the
-
When scanning to receive routine DSC calls, set the scan speed to 0.3
seconds within 6 channels.
Note: If too many channels are being scanned, it may not catch the reception.
key, and through
key on the status display.
5.4)Receiver
1.Auto gain control :Slow
2.Noise reduction
3.Attenuation
4.Clarifier
5.Squelch
6.CW bandwidth
7.Scan
0.Back
5.4.7)Scan
No CH group name
FUNC
01 JRC Tokyo
02
Pacific ABC
03
04
05
06
07
08
5.4.7)Scan
No CH group name
1. Execute
01
JRC Tokyo
2. User channel list
02
Pacific ABC
3. Scan speed (sec)
03
04
05
06
07
08
I D 4 3 1 0 0 1 2 3 4
P o s 8 9 ゚ 5 9 . 0 1 2 3 ' N
1 7 9 ゚ 5 9 . 6 7 8 9 ' E @ 2 3 : 5 9
TEL
RX
TX
S I G
W K R s c a n b a n d s :
2 4 6 8 1 2 1 6 M H z
CANCEL
key.
Operation
:OFF
:OFF
:+000Hz
:OFF
:Narrow
Type
TEL
CW
Type
TEL
CW
TEL
DSC
CW
3.0
0.3
3.0
2 3 : 5 9 ( U T C )
G
PS
JRC Tokyo
Uo1- 001
4357.00
kHz
-----.--
kHz
-S
N o n D S T :
+
M
ENU
D R O B O S :
M
+
ENU
E d t D S T :
M
+
ENU
1
2
3
4-33

Advertisement

Table of Contents
loading

This manual is also suitable for:

Jss-2150

Table of Contents