English SMALL ANGLE GRINDERS DWE4206, DWE4207, DWE4214, DWE4215, DWE4216, DWE4217, DWE4227, DWE4235, DWE4237, DWE4238, DWE4246, DWE4257 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make D WALT one of the most reliable partners for professional power tool users.
WARNING: To reduce the risk of injury, read the instruction manual. Small Angle Grinders Definitions: Safety Guidelines DWE4206, DWE4207, DWE4214, DWE4215, DWE4216, The definitions below describe the level of severity for each DWE4217, DWE4227, DWE4235, DWE4237, DWE4238, signal word. Please read the manual and pay attention to DWE4246, DWE4257 these symbols.
English General Power Tool Safety Warnings non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. WARNING: Read all safety warnings and all c ) Prevent unintentional starting. Ensure the switch instructions. Failure to follow the warnings and is in the off position before connecting to power instructions may result in electric shock, fire and/or source and/or battery pack, picking up or carrying...
English 5) Service debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated a ) Have your power tool serviced by a qualified repair by your operation. Prolonged exposure to high intensity person using only identical replacement parts. This noise may cause hearing loss.
Page 9
English f ) Do not use worn down wheels from larger power to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel’s tools. Wheel intended for larger power tool is not suitable movement at the point of pinching.
English b ) If the use of a guard is recommended for wire Using an Extension Cable brushing, do not allow any interference of the An extension cord should not be used unless absolutely wire wheel or brush with the guard. Wire wheel necessary.
Adjusting and Mounting Guard (Fig. C, D) Soft Start Feature CAUTION: Turn unit off and unplug the tool before making any adjustments or removing or installing DWE4206, DWE4207, DWE4216, DWE4217, DWE4227, attachments or accessories. DWE4237, DWE4238, DWE4246, DWE4257 CAUTION: BEFORE operating the tool, identify which The soft start feature allows a slow speed build-up to avoid an guard adjustment option your tool is set to.
Page 12
English setting guard Adjustment Options WARNING: Use of a damaged flange or guard or fail ure to use proper flange and guard can re sult in injury due to To adjust the guard release lever 9 for desired wheel breakage and wheel contact. See the Accessories adjustment option: Chart for more information.
English NOTICE: Failure to properly seat the wheel before turning installing attachments or accessories. Be sure the the tool on may result in damage to the tool or the wheel. trigger switch is in the OFF position. An accidental start-up can cause injury.
English Variable Speed Dial (Fig. A) RCD before use and clean the ventilation slots daily by blowing dry compressed air into the ventilation slots DWE4246, DWE4257 inaccordance with the below maintenance instructions. The variable speed dial offers added tool control and enables To perform work on a the surface of a workpiece: the tool to be used at optimum conditions to suit the accessory 1.
English 3. nOTE: Only those dust masks suitable for working with lead 4. Once a cut is begun and a notch is established in the paint dust and fumes should be used. Ordinary painting workpiece, do not change the angle of the cut. Changing masks do not offer this protection.
English Working Advice Max. Min. Periphical Threaded [mm] Rotation speed hole length Exercise caution when cutting slots in structural walls. [mm] Slots in structural walls are subject to the country-specific –1 [min. [m/s] [mm] regulations. These regulations are to be observed under all circumstances.Before beginning work, consult the responsible 115 6 22,23...
Page 17
English Grinding and Cutting Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Threaded clamp nut Wire wheels with threaded nut Type 27 guard Wire wheel...
Page 18
English Grinding and Cutting Accessory Chart (cont.) guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Diamond cutting wheels Type 1 Guard Cutting wheel Threaded clamp nut Type 27 Guard...
Page 20
Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)