Advertisement
Daisychaining Ethernet Connection
To connect several cradles to an Ethernet network, the Ethernet
cradles may be daisychained. It is recommended not to connect
more than 4 cradles in order to maintain the optimal baud rate.
Connect the first Ethernet cradle to the Ethernet Switch. Connect the
additional cradles as shown in Figure 7.
A
C
A
D
E
Figure 7 - Daisychaining Ethernet Connection
Key:
A) Power supply without power cord, supplied with the 4SD and
country specific power cord
B) Ethernet hub
C) UTP CAT 5E cable (recommended use)
D) Ethernet Port 1
E) Ethernet Port 2
This is a Class A product. In a domestic environment
this product may cause radio interference in which
case the user may be required to take adequate
measures.
WARNING
Do not use the cradle in a PoE network, i.e. in a
network with PSE able to supply power: there is the
risk to compromise, in irreversible way, the
functionality of the cradle.
WARNING
DOCK DOCK CONTACTS CLEANING PROCEDURE
All exterior metal contacts/connectors exposed to spills, dirt or debris
accumulation require periodic cleaning to ensure best performance
during charging and data transmission.
Use a soft, lint-free dry cloth or lens tissue to clean the product
(contacts and plastics). An antistatic cloth is preferable but you can
also use a cotton cloth. Avoid wool, synthetic cloths or other
materials that can cause electrostatic discharges.
If the contacts are very dirty, clean them with a soft cloth moistened
B
with a diluted non-aggressive cleaning solution or a diluted isopropyl
alcohol solution (20% maximum). A cotton swab may be used only
on hard-to-reach contacts.
Clean the contacts when you see traces of dirt or when you
experience solid connection issues between the terminal and its
dock (device not charging or intermittent communications). It is
C
however suggested to clean the contacts every 6 months (more
often if the environment is dusty).
If the plastic areas are very dirty use only a cloth dampened with
water.
Do not use abrasive or aggressive cleaning agents
or abrasive pads to clean electric contacts, scan
windows or plastics.
CAUTION
Cleaning the Dock Contacts
1.
Remove the power cable before cleaning the contacts.
2.
Use a soft dry cloth as suggested above. If the product is very
dirty, moisten the cloth in a non-aggressive cleaning solution or
diluted isopropyl alcohol solution (20% maximum).
3.
Gently rub the cloth back and forth ONLY along the contacts,
following the directions indicated by the red arrows. Use care
not to leave any cloth residue.
4.
Use a dry cloth to remove any dirt near the contacts area and to
clean the plastic parts. If the plastic parts of the equipment are
very dirty, slightly dampen the cloth with only water.
5.
Repeat steps 2, 3 and 4 using a clean dry cloth.
6.
Allow the cleaning solution to fully evaporate before powering
up the product.
Cleaning the Dock Auxiliary Battery Contacts
1.
Remove the power cable and the Ethernet module before
cleaning the contacts.
2.
Use a soft dry cloth as suggested above. If the product is very
dirty, moisten the cloth in a non-aggressive cleaning solution or
diluted isopropyl alcohol solution (20% maximum).
3.
Gently rub the cloth back and forth ONLY along the contacts,
following the directions indicated by the red arrows. Use care
not to leave any cloth residue.
4.
Use a dry cloth to remove any dirt near the contacts area and to
clean the plastic parts. If the plastic parts of the equipment are
very dirty, slightly dampen the cloth with only water.
5.
Repeat steps 2, 3 and 4 using a clean dry cloth.
6.
Allow the cleaning solution to fully evaporate before powering
up the product.
TECHNICAL FEATURES
Electrical Features
Power supply *
12 VDC ± 5% @ 5A
Consumption
Max 5 A
Spare slot charge time
Elf Std Battery
4h 30
Falcon X3/Elf High
6h 30 (with terminal inserted)
Cap Battery
5h (when terminal is not inserted)
Communication Features
Interface
Ethernet **
Baud Rate
10/100BASE-T
Physical Features
Dimensions
445 x 135 x 105 mm
17.5 x 5,3 x 4.2 in
Weight
(without
1250 g / 44.1 oz
connection cables)
Indicators
Green power-on LED
Bicolored battery charge status LED
Environmental Features
Working temperature***
-10° to +50°C / 14° to 122°F ***
Storage temperature
-20° to +70°C / -4° to 158°F
Humidity
95% without condensation
Electrostatic discharge
4 KV contact / 8 KV air
EN 61000-4-2
*
Use only DL approved power adapters.
** Available in the Ethernet Four Slot Dock only
*** When inserted in the spare slot, standard batteries must be charged at
a temperature ranging from 0° to 40 °C.
When inserted in the spare slots, high capacity batteries must be
charged at a temperature ranging from 0° to 35 °C.
At higher values the charging may slow down.
FCC COMPLIANCE
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
Modifications or changes to this equipment without the expressed
written approval of Datalogic could void the authority to use the
equipment.
This device complies with PART 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference which may cause
undesired operation.
©2010-2018 Datalogic S.p.A. and/or its affiliates • All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S.A. and the E.U. Elf and
Falcon are trademarks of Datalogic S.p.A. and/or its affiliates.
All other brand and product names may be trademarks of their respective
owners.
Advertisement
