Advertisement
Operation Guide 3534
Alarm
You can set an alarm with hour, minute, month, and
Alarm on
Mode
day. When the alarm is on, the alarm sounds for 20
indicator
indicator
seconds at the preset time. When the Hourly Time
Signal is on, the watch beeps every hour on the hour.
Month
Day
Alarm Types
The types of alarm you get depends on the
information you set.
To set a daily alarm
Set the hour and minute for the alarm time. Set "–"
for the month and "– –" for the day (see step 3 under
"To set the alarm time"). This type of setting causes
Hour
Minute
the alarm to sound every day at the time you set.
Hourly time signal on indicator
EN-10
2. Press C to change the selection in the following sequence.
C
Hour
Day
C
C
3. Press B to increase the selected digits. Holding down B changes the number
at high speed.
The format (12-hour and 24-hour) of the alarm time matches the format you
select for normal timekeeping.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
4. After you set the alarm time, press A to return to the Alarm Mode.
If you do not operate any button for a few minutes while a selection is flashing,
the flashing stops and the watch goes back to the Alarm Mode automatically.
EN-12
Timer
The countdown timer can be set within a range of
Current time
1 second to 24 hours. When the countdown reaches
zero, an alarm sounds for 10 seconds or until you
Mode indicator
press any button.
To set the countdown time
1. Press A while in the Timer Mode. The hours digit
flashes on the display because it is selected.
2. Press C to change the selection in the following
sequence.
Hours
Seconds
Hours
Minutes
EN-14
3. Stop the timer and then press A until the countdown time is reset to its starting
value.
When the end of the countdown is reached and auto repeat timing is off, the
alarm sounds for 10 seconds or until you stop the alarm by pressing any button.
Countdown timing stops, and the countdown time is automatically reset to its
starting value after the alarm stops.
To switch auto repeat timing on and off
1. Press A while in the Timer Mode. The hours digit
flashes on the display because it is selected.
2. Press D to switch auto repeat on and off.
Auto repeat on indicator
EN-16
Stopwatch
The Stopwatch Mode lets you measure elapsed
Current time
time, split times, and two finishes. The range of the
stopwatch is 23 hours, 59 minutes, 59 seconds.
Mode indicator
To measure elapsed time
1. Press B to start the stopwatch.
2. Press B to stop the stopwatch.
You can resume the measurement operation by
pressing B again.
3. Press A to clear the stopwatch to all zeros.
Minutes
For the first 60 minutes, the display shows
minutes, seconds, and 1/100 second. After
Seconds
60 minutes, the display format changes to show
hours, minutes, and seconds.
1/100 second
EN-18
C
Minute
Month
C
C
Minutes
Seconds
C
To set a date alarm
Set the month, day, hour and minute for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
To set a 1-month alarm
Set the month, hour and minute for the alarm time. Set "– –" for the day (see step 3
under "To set the alarm time"). This type of setting causes the alarm to sound every
day at the time you set, only during the month you set.
To set a monthly alarm
Set the day, hour and minute for the alarm time. Set "–" for the month (see step 3
under "To set the alarm time"). This type of setting causes the alarm to sound every
month at the time you set, on the day you set.
To set the alarm time
1. Press A while in the Alarm Mode until the hour digits start to flash on the
display. The hour digits flash because they are selected.
At this time, the alarm is automatically switched on.
To stop the alarm
Press any button to stop the alarm after it starts to sound.
To switch an alarm and Hourly Time Signal on and off
Press B while in the Alarm Mode to change the status of an alarm (see "Alarm
Types" on page EN-10) and Hourly Time Signal in the following sequence.
B
B
Both off
Alarm only
Alarm on indicator
Hourly time signal on indicator
3. Press B to increase the selected number. Holding down B changes the
number at high speed.
To set the starting value of the countdown time to 24 hours, set 0:00' 00.
4. After you set the countdown time, press A to return to the Timer Mode.
If you do not operate any button for a few minutes while a selection is flashing,
the flashing stops and the watch goes back to the Timer Mode automatically.
To use the countdown timer
1. Press B while in the Timer Mode to start the countdown timer.
2. Press B again to stop the countdown timer.
You can continue countdown timer operation by pressing B.
3. Press A to return to the Timer Mode.
When the end of the countdown is reached while auto repeat is on, the alarm
sounds, but the starting countdown time is reset and countdown timing starts
again automatically whenever the countdown reaches zero. You can stop timing
by pressing B, and manually reset to the starting countdown time by pressing
A.
To record split times
1. Press B to start the stopwatch.
2. Press A to display the timing up to that point. Stopwatch timing continues
internally.
3. Press A to clear the split time and to continue time measurement on the display.
You can repeat steps 2 and 3 as many times as you want.
4. Press B to stop the time measurement.
5. Press A to clear the stopwatch to all zeros.
To time first and second place finishes
1. Press B to start the stopwatch.
2. Press A when the first finisher crosses the line, and record the time.
3. Press B when the second finisher crosses the line.
4. Press A to display the finishing time of the second finisher.
5. Press A again to clear the stopwatch to all zeros.
EN-11
B
Hourly Time
Both on
Signal only
B
EN-13
EN-15
EN-17
EN-19
Advertisement
