Wow Zino Paddle Board Manual page 3

ASSEMBLY INSTRUCTIONS AND PROPER INFLATION INSTRUCTIONS:
1. Unfold your board on a flat surface without sharp objects that could puncture the bladder.
2. Locate the valve at the back of the board and unscrew the valve cap cover.
3. Then turn the valve stem counter clockwise until the middle pin is in the upright position.
4. Find your included high pressure hand pump, pressure gauge, and hand pump hose.
5. First attach your pressure gauge to the high pressure hand pump. Then second connect your hose to
your high pressure gauge. Now your high pressure hand pump is ready to inflate your product.
6. To inflate your paddle board insert your hose with special inflation adaptor into the valve body
and turn 1/4 turn to lock in place.
7. Start pumping, taking long strokes. The longer the strokes the less number will be required. Once you reach
10 psi you will need to take much shorter strokes to inflate to the full 12 to 15 psi.
IN ORDER FOR YOUR INFLATABLE PADDLE BOARD TO FUNCTION PROPERLY YOU MUST INFLATE
TO 12 to 15 PSI SO YOUR BOARD IS RIGID RESULTING IN YOUR PRODUCT TO BE MORE STABLE
AND GLIDE EASIER THROUGH THE WATER.
You can shorten this process by using a small vacuum pump with the same special adaptor to
inflate the majority of your inflatable paddle board. Then completing it with your included high
pressure hand pump to the correct 12 to 15 PSI. Note to make sure you read the recommend 12
to 15 PSI on your provided pressure gauge when completing your inflation with your high pressure
hand pump.
8. Once proper inflation is achieved remove your high pressure pump hose from the valve body and
then screw your valve cap cover into the lock position.
CENTER FIN INSTALLATION:
1. Slide the fin base into fin box.
2. Slide fin all the way to back of the fin box
3. Insert fin retention pin through slot
4
PRODUCT USE:
Stand Up Paddle Boarding can be mastered in a very short period of time.
Here are a few tips to review:
1. Before you start, adjust your paddle so it is 8-10" above your head when touching the ground.
2. Mount the paddle board by kneeling on the deck pad just in front of the carrying strap, shoulder
width apart. (Paddle should be in front of you with the blade towards the nose).
3. When comfortably balanced, raise the paddle, placing one hand over the top and the other hand
about two feet down the shaft. (the blade of the paddle should point up).
4. Proceed to paddle on your knees until comfortable.
5. When ready to stand, place paddle back in front of you and stand up slowly. Be sure you are away
from anything you could hit your head on if you fall.
6. Retrieve the paddle and proceed with your knees slightly bent under your shoulders, back straight,
and look straight ahead, not down at your feet.
7. To turn to the left make a wide sweep of the paddle on the right
or drag the paddle from the tail on the left.
8. To turn to the right make a wide sweep of the paddle on the left
or drag the paddle from the tail on the right.
DEFLATION INSTRUCTIONS:
1. Before deflating your paddle board clear any water or debris out of the valve area.
2. Unscrew the valve cap cover from the valve. Slowly press down on the center valve stem to start letting air out
of the board. There will be an initial burst of air, but that will slow down very quickly. Once the air flow has slowed
down, press the valve stem all the way down and turn it clockwise to lock it into the "open" position.
3. Let the board deflate for approximately two minutes.
4. Remove the center fin by unscrewing the fastener and slide the fin out of the fin box.
5. Let the product fully dry.
**Always use the supplied inflatable fin protector to prevent fin damage and bending when folding
and storing your product.
6. Fold up the board starting from the nose toward the tail.
NOTE DO NOT ROLL YOUR BOARD PLEASE FOLD ONLY!
7. Fold the board tight enough so it ends up about 12-14" in diameter. Then you can store your
paddle board with your included product accessories in your included custom back pack.
STORAGE AND CARE:
• When the inflatable product is not being used, we recommend that you store it in a covered, shaded area.
This will help protect it against ultraviolet (UV) rays and extend the life of the product.
• Do not leave board inflated in direct sunlight for long periods of time when not in use.
• Clean the product completely with a mild soap and fresh water.
NEVER USE PETROLEUM BASED PRODUCTS OR SOLVENTS FOR CLEANING.
• Product should be completely dry and remain dry while stored to prevent mildew build up.
• Fold the product loosely and place in the included custom backpack.
• Store in a clean dry place that is a climate control environment.
Do not store in extreme conditions (i.e. above 150F or below -10F)
• Do not store product directly on concrete surface.
• Secure the product to prevent unauthorized or unsupervised use.
5