Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Belden Miranda SSP-3801
Summary of Contents for Belden Miranda SSP-3801
- Page 1 SSP-3801 Quick Installation Guide M931-9902-100 3 September 2013...
- Page 2 Copyright & Trademark Notice Copyright © 2013, Miranda Technologies Partnership. All rights reserved. Belden, Belden Sending All The Right Signals, and the Belden logo are trademarks or registered trademarks of Belden Inc. or its affiliated companies in the United States and other jurisdictions.
-
Page 3: Table Of Contents
Table of Contents 1 Introduction ......... . . 1 What’s included with your product. - Page 4 Table of Contents...
-
Page 5: Introduction
Introduction This chapter provides an overview of what is included in your SSP-3801 package and as well as an overview of the features of the SSP-3801 card. This chapter contains the following sections: What’s included with your product ........... . 2 About the SSP-3801 card . -
Page 6: What's Included With Your Product
Introduction What’s included with your product What’s included with your product Each SSP-3801 package consists of two separate hardware components: • One HD/SD SSP-3801 card • One SSP-3801 rear connector panel Component Front Rear HD/SD Solid- State Playout card SSP-3801 rear connector panel You can access and download the complete SSP-3801 documentation from the Miranda Support Portal:... -
Page 7: About The Ssp-3801 Card
SSP-3801 SSP-3801 Quick Installation Guide About the SSP-3801 card The SSP-3801 is a playout server card that consists of two circuit boards assembled together: • The main board carries the bulk of the electronics with a connector that interfaces with the SSP-3801 rear connector panel. -
Page 8: Ssp-3801 Rear Connector Panel
Introduction SSP-3801 rear connector panel SSP-3801 rear connector panel Like other Densité 3 cards, the SSP-3801 card interfaces with a separate rear connector panel that must be fixed to the rear of the Densité 3 frame. Figure lists the required input/output connectors featured on the rear connector panel. -
Page 9: Densité 3 Frame's Local Control Panel
SSP-3801 SSP-3801 Quick Installation Guide Densité 3 frame’s local control panel Like all other cards installed in a Densité 3 frame, the SSP-3801 is connected to the frame’s controller card, which handles all interaction between the cards and the outside world. The controller also supports remote operation via its Ethernet ports, and local operation using its integrated control panel (figure 1-4). - Page 10 Introduction Densité 3 frame’s local control panel...
-
Page 11: Installing The Ssp-3801 Card
Installing the SSP-3801 card This chapter explains how to install the SSP-3801 card in a Densité 3 frame, as well as how to attach the cables. It also explains how to start the card and read its start-up status LEDs. This chapter has the following sections: Installing the rear connector panel . -
Page 12: Installing The Rear Connector Panel
Installing the SSP-3801 card Installing the rear connector panel Installing the rear connector panel The SSP-3801 rear connector panel must be installed in the Densité 3 frame before the card can be inserted. Note: All Densité 3 cards and rear panels can be installed with the frame power on. -
Page 13: Installing The Ssp-3801 Card
SSP-3801 SSP-3801 Quick Installation Guide Installing the SSP-3801 card Once a matching rear connector panel has been installed, you can install the SSP-3801 card. To install the SSP-3801 card, follow these steps: 1 Open the front panel of the frame. 2 Slide the SSP-3801 card into the slot and push gently on the handle to seat the connectors (figure 2-2). -
Page 14: Cabling The Ssp-3801 Card
Installing the SSP-3801 card Cabling the SSP-3801 card Cabling the SSP-3801 card Cabling the SSP-3801 depends upon your intended use. Note that the scope of this document is limited to setting up the SSP-3801 card for basic start-up functionality. As such, you should ensure that the following connections are made to the rear connector panel of the SSP-3801 card. -
Page 15: Starting The Ssp-3801 Card
SSP-3801 SSP-3801 Quick Installation Guide Starting the SSP-3801 card Once the SSP-3801 rear connector panel and card have been installed, power up the Densité 3 frame and ensure that the SSP-3801 card is running properly. To start the SSP-3801 card: 1 If it is not already done, power up the Densité... -
Page 16: Setting And Verifying The Ssp-3801 Default Settings
Installing the SSP-3801 card Setting and verifying the SSP-3801 default settings Setting and verifying the SSP-3801 default settings In preparation for other configuration tasks, we recommend that you verify and ensure some of the SSP-3801 settings are set to their default values, as well as taking note of the SSP-3801 card’s current IP address. -
Page 17: Logging Into The Ssp-3801 Card's Web Interface
SSP-3801 SSP-3801 Quick Installation Guide Logging into the SSP-3801 card’s web interface The SSP-3801 web interface provides you with remote access to all of the parameters and settings specific to a particular card. The following instructions demonstrate how to log into the SSP-3801 web interface from any client computer that is on the same network as the SSP-3801 card. - Page 18 Installing the SSP-3801 card Logging into the SSP-3801 card’s web interface...
Need help?
Do you have a question about the Miranda SSP-3801 and is the answer not in the manual?
Questions and answers