Dunster House MonkeyFort Wilderness 2 Installation Manual

Hide thumbs

page of 20

/ 20
Bookmarks

Quick Links

Download this manual

Manufacturer:

Dunster House Ltd.

Caxton Road

Bedford

Bedfordshire

England

MK41 0LF

Customer Service department:

cs@dunsterhouse.co.uk

www.dunsterhouse.co.uk

Packed with PS601

Installation Manual

MonkeyFort Wilderness 2

PS601

Hammer

Ladder

for

Two adults (and tools) are required for assembly

Socket

wrench

Tape

measure

Screwdriver

Cordless drill/drill

Spirit level

Need help?

Do you have a question about the MonkeyFort Wilderness 2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Dunster House MonkeyFort Wilderness 2

Page 1 Installation Manual MonkeyFort Wilderness 2 Manufacturer: Dunster House Ltd. Caxton Road Bedford Bedfordshire PS601 England MK41 0LF Customer Service department: cs@dunsterhouse.co.uk Two adults (and tools) are required for assembly www.dunsterhouse.co.uk Spirit level Hammer Tape measure Ladder Socket Packed with PS601...
Page 2 Fax: (01234) 224497 Post: Dunster House Ltd., Caxton Road, Elms Farm Industrial Estate, Bedford MK41 0LF, England. Our Customer Service department is open 9 a.m. - 5 p.m. Monday to Friday and aim to respond within 2-3 hours of receipt, however, this may be longer during busy periods. Please include your Sales Order (SO) number in any correspondence with Customer Services to enable them to locate your file.
Page 3 Bolt Configuration Please use this page to ensure that the fixings for your play system are installed correctly. You must use these claw washers in every location where you are instructed to use an M10 (10mm diameter) bolt. These pronged washers create a sleeve for the square ‘neck’...
Page 4 Assembly Instructions for MonkeyFort Wilderness II Maintenance of the MonkeyFort is very important and should be carried out at the beginning of each season, as well as at regular intervals during usage, to ensure that the Fort remains safe. Failure to carry out these checks could cause the Fort to overturn or become a hazard. The points you should check to maintain this Fort include the following: -Check all nuts and bolts for tightness and tighten when required.
Page 5 Assembly Instructions for MonkeyFort Wilderness II Please retain these instructions for future reference. Components (sizes in mm) 1 of M10x170mm square shoulder coach bolt 1 of M10x145mm square shoulder coach bolt 1 of M10x130mm square shoulder coach bolt 2 of M10x120mm square shoulder coach bolt 1 of M10x110mm square shoulder coach bolt...
Page 6 Assembly Instructions for MonkeyFort Wilderness II This play system is intended for family domestic use and to be used for outdoor use only. This climbing frame is suitable for children aged between 3-14 years and up to a maximum weight of 50kg per child and a maximum of 4 children at any time but only one child can play on the tower platform.
Page 7: Step 2 - Required Components
Assembly Instructions for MonkeyFort Wilderness II Step 2 - required components 1 of C40239A - 86x43x2350 2350 1 of C40240A - 86x43x2500 2500 28 of 4x50mm countersunk screw 7 of C4038A - 44x44x550 - rungs Lay the items on the ground first and position the components before fixing. Make sure the grooves on the rungs are facing the same direction as depicted.
Page 8 Assembly Instructions for MonkeyFort Wilderness II Step 3 - required components 1 of Horizontal ladder (Step 2) 2 of Vertical ladders (Step 1) 3 of C4018A - 70x35x400 3 of C4017A - 70x35x260 4 of M10x100mm coach bolt, 8 of M10x20mm washer, 4 of M10 nut, 4 of Green 10mm cap, 6 of 4.8x95mm countersunk screw...
Page 9 Assembly Instructions for MonkeyFort Wilderness II Step 4 - required components 1 of C4089A - 90x19x900 1 of C40238A - 86x43x2225 2225 1 of M10x100mm square shoulder coach bolt, 4 of 4x50mm countersunk screw 2 of M10x20mm washer, 1 of M10 nut, 1 of Green 10mm cap, 1 of Claw washer M10x20mm washers C40238A - 86x43x2225...
Page 10 Assembly Instructions for MonkeyFort Wilderness II Green 10mm cap (top) M10 nut M10x20mm washer Green 10mm cap (base) M10x20mm washer M10x90mm square Claw washer shoulder coach bolt Green 10mm cap (top) Claw washer M10 nut M10x90mm square M10x120mm washer shoulder coach bolt Green 10mm cup (base) Step 6 - required components M10x120mm washer...
Page 11 Assembly Instructions for MonkeyFort Wilderness II Step 7 - required components 10 of C40112A - 121x15x900 40 of 4.5x35mm countersunk screw C40112A - 121x15x900 4.5x35mm countersunk screw C40112A - 121x15x900 Step 8 - required components 1 of C4013A - 90x19x600 2 of 4x50mm countersunk screw C4013A should be flush with platform decking.
Page 12 Assembly Instructions for MonkeyFort Wilderness II Step 9 - required components 32 of 4x50mm 2 of C4044A - 70x35x1200 8 of C4013A - 90x19x600 countersunk screw 1200 14 of Clave nut 14 of M6x35mm dome bolt 7 of Climbing stone 14 of M6x12mm washer Pre-drill holes using 8mm drill bit.
Page 13 Assembly Instructions for MonkeyFort Wilderness II Step 11 - required components 1 of C4044A - 70x35x1200 2 of 5x70mm countersunk screw 1200 5x70mm countersunk screw C4044A - 70x35x1200 5x70mm countersunk screw C4044A - 70x35x1200 Step 12 - required components 4 of 4x50mm countersunk screw 1 of C40242A - 35x35x1165 1165 C40242A and C40240A should be flush at...
Page 14 Assembly Instructions for MonkeyFort Wilderness II Step 13 - required components 2 of C40244A - 35x35x635 1 of C40243A - 35x35x713 6 of 4x50mm countersunk screw C40244A - 35x35x635 C40243A - 35x35x713 C40244A - 35x35x635 Step 14 - required components 1 of 2300x710 4 of 5x70mm 12 of M5x10mm washer...
Page 15 Assembly Instructions for MonkeyFort Wilderness II Figure 1 4 of 3x20mm long screws and 4 of M5x10mm washers Locate the centre of the green material C40243A - 35x35x713 and using 4 of 3x20mm countersunk 1200x1900 material screws and M5x10mm washers, attach the green material to the top of the C40243A - 35x35x713 C40243A - 35x35x713...
Page 16 Assembly Instructions for MonkeyFort Wilderness II Step 16 - required components 2 of M6x40mm 2 of Clave nut 1 of Slide dome bolt Slide M6x40mm Holes need to be dome bolt pre-drilled using the Slide 8mm drill bit provided. To fix the slide to the platform, lift the slide onto the platform and position it so that it is central on the platform and doesn't stick out from the platform edge.
Page 17 Assembly Instructions for MonkeyFort Wilderness II Step 17 - required components 2 of C40245A - 70x35x2140 1 of C4016A - 70x35x900 1 of PSAF50DEG bracket 2140 4 of 4x50mm countersunk screw 2 of 5x70mm countersunk screw A-Frame PSAF50DEG bracket 4x50mm countersunk C4016A - 70x35x900 screws...
Page 18 Assembly Instructions for MonkeyFort Wilderness II Step 19 - required components 1 of A-Frame (from Step 17) 3 of 5x70mm 1 of Swing beam (from Step 18) countersunk screw Swing beam 5x70mm countersunk screw 5x70mm countersunk screw A-Frame Step 20 - required components 1 of M10x110mm square shoulder coach bolt, 1 of M10x170mm square shoulder coach bolt, 3 of M10x20mm washer, 1 of M10 nut,...
Page 19 Assembly Instructions for MonkeyFort Wilderness II Step 21 - required components 1 of Swing seat 2 of M10x70mm hex head 4 of Ground 2 of M10x60mm hex head bolt, 6 of anchor screw, 2 of M10x30mm M10x30mm washer, 2 of M10x20mm washer, washer 2 of M10 nut, 2 of Green 10mm cap Clip the swings onto the swing hooks that have...
Page 20 Slide Care Advice / Maintenance To ensure that you enjoy the maximum usage of your slide, please take note of and follow the maintenance/advice contained on this page. You MUST install the slide as per the installation instructions in the location it is intended to go. You CANNOT install the slide in any other location on the platform otherwise any warranty claims will be rendered void.

This manual is also suitable for:

Ps601