Table of Contents
Advertisement
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times
and beeps will sound. The option will not be enabled.
3D ZONE WASH
Option works with one rack at once. In particular, we
recommend to use it with Mixed and Intensive cycles -
thanks to the additional 3D water jets placed on the bottom
of the cavity, 3D ZONE WASH option allows to save energy
or to increase the washing performance of the dishwasher:
• 3D ZONE WASH + AUTO MIXED CYCLE: it allows to reduce
energy consumption up to 40%.
• 3D ZONE WASH + AUTO INTENSIVE CYCLE: it increases
the washing performances up to 40%. Ideal for very soiled
mixed loads, e.g. pans and saucepans, dishes with heavy
encrustation or difficult-to-clean crockery (grater, vegetable
mill, dirty cutlery).
How to activate the option:
1. Select a compatible cycle
2. By default the appliance washes dishes in all racks. To wash
only the specific rack, press this button repeatedly:
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (only cutlery rack)
shown on the display (option is OFF and the appliance will
wash dishes in all racks).
Remember to load the upper or lower rack only, and to reduce
the amount of detergent accordingly.
If upper rack is removed, please apply detergent directly
to tub instead of detergent dispenser.
DELAY
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
1. Press the DELAY button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start
of the selected wash cycle will be increased.
2. Select the wash program, press the START/Pause button
and within 4 seconds close the door: the timer will begin
counting down.
3. Once this time has elapsed, the indicator light «h» switches
off and the wash cycle begins.
To adjust the delay time and select a shorter period of time,
press the DELAY button. To cancel it, press the button repeatedly
until the selected delayed start indicator light «h» switches off.
The DELAY function cannot be set once a wash cycle has
been started.
4
SHORT TIME
This option can be used to reduce the duration of the main
programs while maintaining the same washing and drying
performance levels.
After selecting the program, press the SHORT TIME button
and the indicator light will switch on. To deselect the option,
press the same button again.
EXTRA DRY
To improve the drying of the dishes, after selecting the program,
press the EXTRA DRY button and the indicator light comes on.
A higher temperature during the final rinse and an extended
drying phase allow for improving drying. To deselect the option,
press the same button again. The EXTRA DRY option results
in the lengthening of the wash cycle.
TABLET (Tab)
This setting allows you to optimize the performance of the pro-
gram according to the type of detergent used.
Press the START/PAUSE button for 3 seconds (the correspon-
ding symbol will light up) if you use combined detergents
in tablet form (rinse aid, salt and detergent in 1 dose).
If you use powder or liquid detergent, this option should
be off.
OPERATION INDICATOR
A LED light projected on the floor indicates that the dishwasher
is working. One of the following operating modes can be
selected:
a) Disabled function.
b) When the cycle starts the light goes on for few seconds, stays
off during the cycle and flashes at the end of the cycle.
c) The light stays on during the cycle and flashes at the end
of the cycle (default mode).
If the delayed start was set, the light goes on either for the first
few seconds or the entire duration of the countdown, based
on whether mode b) or c) was set.
The light goes off every time the door is opened. To select
the mode you prefer, switch on the machine, hold down button
P until one of the three letters appears on the display, press
button P until you reach the desired letter (or mode), hold down
button P to confirm the selection.
Advertisement
Table of Contents
