iRobot Roomba j8+ Robot Vacuum Manual

Table of Contents

Contents

1 Overview of the device
- 1.1 Overview of the Roomba Robot Vacuum
- 1.2 Overview of the Clean Base Automatic Dirt Disposal
2 Using your Roomba Robot Vacuum
3 Care and Maintenance
4 Troubleshooting
5 iRobot Customer Care
6 Documents / Resources
- 6.1 References
- 6.2 Download manual

Overview of the device

Overview of the Roomba ® Robot Vacuum

Top View
Bottom View

Overview of the Clean Base™ Automatic Dirt Disposal

Front View
Top View
Back View
Bottom View

Using your Roomba^® Robot Vacuum

Positioning the Clean Base™ Automatic Dirt Disposal

Positioning the Clean Base
*Objects are not to scale.

Note:
Do not place your Clean Base Automatic Dirt Disposal in direct sunlight. Ensure the area around the dock is free of clutter to improve docking performance.

To prevent the risk of your robot falling downstairs, ensure that the charging station is placed at least 4 feet (1.2 meters) away from stairs.

Download the iRobot Home App and connect to Wi-Fi^®

Follow step-by-step instructions to set up your Roomba.
Set up Precision Vision Navigation™ to avoid obstacles in real time.
Set an automatic cleaning schedule and customize cleaning preferences.
Create smart maps to tell your robot where and when to clean.

Charging

Light Ring Spiral While Charging

White Spiral: charging
Red Spiral: charging, low battery
A solid white light will indicate the battery charge percentage of your robot

Place the robot on the charging station to activate the battery.
Note: Your robot comes with a partial charge, but we recommend that you charge the robot for 3 hours prior to starting the first cleaning job.
When your robot is fully charged, the light ring indicator will intermittingly pulse white at the rear.

The robot uses a small amount of power whenever it is on the charging station. You can put the robot in a further reduced power state when not in use. To put your robot into reduced power standby mode, remove the dust bin and tap the clean button 5 times. To exit reduced power standby mode, place your robot on the charging station and tap the clean button. For more details on this Reduced Power Standby Mode, refer to the FAQ page on our website.
For long-term storage, turn off the robot by removing it from the charging station and holding down the clean button for 3 seconds with one wheel off the ground. Store the robot in a cool, dry place.

Cleaning

Just press the clean button

Tap to Start / Pause / Resume
Hold for 2-5 seconds to end a job

Your robot will automatically explore and clean your home in neat rows, avoiding obstacles using its front-facing camera. It will return to the charging station at the end of a cleaning job and whenever it needs to recharge.
Your robot is able to recognize and avoid objects. However, it is still recommended to remove excess clutter before cleaning.
To end a job and send the robot back to its charging station, hold the clean button down for 2-5 seconds. A blue light ring pattern will indicate that the robot is seeking the charging station.
When your robot detects an especially dirty area, it will engage Dirt Detect™ mode, moving in a forward/backward motion to clean the area more thoroughly. The light ring indicator will flash blue.
When the robot senses its bin needs to be emptied, the light ring indicator will illuminate in a red sweeping motion toward the rear.

Troubleshooting

Your robot will tell you something is wrong by playing an audio alert and turning the light ring indicator red. Press the clean button or tap the bumper for details. Check the iRobot Home App for further support.
After 90 minutes of inactivity off the charging station, the robot will automatically end its cleaning job.
To factory reset your robot, remove the dust bin and hold the clean button down for seven (7) seconds. A sound will let you know when the factory reset has been completed. Press the clean button down once more to confirm.

Battery Safety & Shipping

For best results, only use the iRobot Lithium Ion Battery that comes with your robot.

Lithium ion batteries and products that contain lithium ion batteries are subject to stringent transportation regulations. If you need to ship this product for service, travel or any other reason, you MUST follow the below shipping instructions.

Battery MUST be turned off before shipping.
Turn off the battery by removing the robot from the charging station and holding down the clean button for 3 seconds with one wheel off the ground. All indicators will turn off.
Package the robot securely for shipping.
If you need further assistance, contact our Customer Care team or visit global.irobot.com.

About Your Automatic Dirt Disposal

While cleaning, your robot will automatically return to the dirt disposal to empty its bin and recharge as needed.

The dirt disposal's LED indicator will turn solid red when a new bag is needed. If a clog is detected, the dirt disposal will trigger additional attempts to automatically clear the clog.

Note:
If you place your robot on the dirt disposal by hand, it will not empty automatically. In this case, use the iRobot Home App or hold the button down for 2-5 seconds.

Care and Maintenance

Care and Maintenance Instructions

To keep your robot running at peak performance, perform the procedures on the following pages.

There are additional instructional videos in the iRobot Home App. If you notice the robot picking up less debris from your floor, empty the bin, clean the filter and clean the brushes.

Part	Care Frequency	Replacement Frequency*
Bin	Wash bin as needed
Filter	Clean once a week (twice a week if you have a pet). Do not wash.	Every 2 months
Full Bin Sensor	Clean every 2 weeks
Front Caster Wheel	Clean every 2 weeks	Every 12 months
Edge-Sweeping Brush and Multi-Surface Brushes	Clean once a month (twice a month if you have a pet)	Every 12 months
Sensors and Charging Contacts	Clean once a month
Camera Window	Clean and inspect once a month
Bags		Bags should be replaced when prompted by the LED indicator / app
Dock Charging Contacts and Visual Docking Target	Once every month
Blower Cover inside canister	Once every month (remove debris from blower cover)

Note:
iRobot manufactures various replacement parts and assemblies. If you think you need a replacement part, please contact iRobot Customer Care for more information.

* Replacement frequency may vary. Parts should be replaced if visible wear appears.

Emptying the Bin

Press bin release button to remove bin.
Open bin door to empty bin.
Place bin back in the robot.

Cleaning the Filter

Remove the bin. Remove the filter by grasping both ends and pulling out.
Remove debris by tapping the filter against your trash container.
Reinsert filter with ridged grips facing out. Place bin back in the robot.

The robot will not run if the filter is not installed correctly.
Replace the filter every two months.

Cleaning the Full Bin Sensors

Remove and empty the bin.
Wipe the inner sensors with a clean, dry cloth
Wipe the bin door with a clean, dry cloth.
Clear any debris from the vacuum path.

Washing the Bin

Do not wash the filter. Remove the filter before washing the bin.

Release the bin, remove the filter, and open the bin door.
Rinse the bin using warm water.

Note: Bin is not dishwasher safe.
Make sure bin is completely dry. Reinsert filter and place bin back in the robot.

Cleaning the Edge-Sweeping Brush

Use a coin or small screwdriver to remove the screw holding the Edge- Sweeping Brush in place.
Pull to remove the Edge-Sweeping Brush. Remove any hair or debris, then reinstall the brush.

Cleaning the Front Caster Wheel

Pull firmly on the front wheel module to remove it from the robot.
Pull firmly on the wheel to remove it from its housing (see illustration below).
Remove any debris from inside the wheel cavity.
Reinstall all parts when finished. Make sure the wheel clicks back into place.

A front wheel clogged with hair and debris could result in damage to your floor. If the wheel is not spinning freely after you have cleaned it, please contact Customer Care.

Cleaning the Multi-Surface Brushes

Pinch the brush frame release tab, lift the tab, and remove any obstructions.
Remove the brushes from the robot. Remove the brush caps from the ends of the brushes. Remove any hair or debris that has collected beneath the caps. Reinstall the brush caps.
Remove any hair or debris from the square and hexagonal pegs on the opposite side of the brushes.
Reinstall the brushes in the robot. Match the shape of the brush pegs with the shape of the brush icons in the cleaning head module.

Cleaning the Sensors, Camera Window and Charging Contacts

Wipe sensors, camera window and charging contacts with a clean, dry cloth.

Note: Inspect the camera window. If you notice any cracks, please contact Customer Care.

Replacing the Bag

Lift up on the canister lid to open.
Pull up on the plastic card to remove the bag from the canister.

Note: This will seal the bag so dust and debris cannot escape.
Discard the used bag.
Install a new bag, sliding the plastic card into the guide rails.
Press down on the lid making sure it is completely closed.
Note: To achieve optimal performance with your robot and automatic dirt disposal, clean and/or replace your robot's filter as needed.

Cleaning the Visual Docking Target and Charging Contacts

Inspect the visual docking target and charging contacts to make sure they are clear of debris. Wipe with a clean, dry cloth.

Note: Do not spray cleaning solution directly onto sensors or into sensor openings.

Removing Debris from Blower Cover

Inspect blower cover for any lint or debris builtup, and wipe with a clean dry cloth to remove.

Troubleshooting

Your dirt disposal will tell you if something is wrong via an LED indicator on the front of the canister and through the iRobot Home app.

LED Indicator	Common Error	How to Fix
Solid Red	Bag full or missing	Replace bag if it is full or missing. Make sure the bag is securely inserted. If problem persists, remove any debris from the port on the bottom of your robot and the dirt disposal.
Blinking Red	There is a leak or a clog in the dock evacuation path	Make sure the canister lid is pushed down and firmly sealed. Hold the clean button on your robot down for 2 seconds to manually empty the bin. Remove any debris from the port on the bottom of your robot and dirt disposal. Unplug the dirt disposal from the wall. Place it on its side and inspect the debris evacuation tube for debris. If necessary, remove the tube to clear any debris.

This product has been equipped with a thermal protector designed to protect against damage due to overheating. If the protector operates, the motor will stop running. If this happens, unplug the unit, allow to cool for 30 minutes, clear any obstructions from the evacuation port and evacuation tube, and plug the unit back in.

iRobot Customer Care

USA & Canada
If you have questions or comments about your Roomba^® robot vacuum, please contact iRobot before contacting a retailer.
You can start by visiting global.irobot.com for support tips, frequently asked questions and information about accessories. This information can also be found in the iRobot Home App. If you need further assistance, call our Customer Care team at (877) 855-8593.
iRobot USA Customer Care Hours
- Monday to Friday, 9AM – 9PM Eastern Time
- Saturday and Sunday 9AM – 6PM Eastern Time
Outside USA & Canada
Visit global.irobot.com to:
- Learn more about iRobot in your country
- Get hints and tips to improve your Roomba^® robot vacuum's performance
- Get answers to questions
- Contact your local support center