Cellularline easyfit touch - Fitness Tracker Touch Screen Wristband Manual

FUNCTIONS

00:00
Time

Steps

Distance

Calories

Alarm clock

Sleep monitor

Move Alert

Call ID Display

Message Push

Bluetooth

Autodyne

Bluetooth broadcast

COMPATIBILITY

The Smart Wristband supports the following mobile devices, only:

IOS: OS must be IOS 7.0 or later, Bluetooth 4.0; Examples: iPhone 4S, iPhone5, iPhone5S, iPhone6, iPhone6Plus, iPod Touch5, etc.

Android: OS must be Android 4.3 or later, Bluetooth 4.0; Examples: Samsung S4, Note3, etc.

QUICK START GUIDE

The bracelet should be charged for 30 min. before use. Pull out the USB connector, as shown below, and insert the connector into a 5V/1A USB port for charging. The indicator light will stop flashing when the device is fully charged (after 30 minutes).

Install the App: Go to the App store or play store, download the CELLULARLINE-EASYFIT App and install it. To use the CELLULARLINE-CELLULARLINEEASYFIT App, make sure your mobile device is connected to the Internet via Wi-Fi or 3G.

Open the CELLULARLINE-EASYFIT App. Log in if you have an account, or register to set up a new account.

Operating Instructions

You can operate the bracelet by "wrist gesture" or "screen touch".

It's convenient to check the time by "wrist gesture".

"Screen touch"

Function	Operation
Start-up	Hold your finger down on the bracelet screen
Turning on the screen	Click the screen or turn your wrist over
Shut-down	Swipe left to right on the interface then switch to Hold your finger down on the screen to turn off the device
Switching functions	Swipe left to right
Flip-Over	Click on the screen
Confirm	Hold your finger down on the screen

NB: Functions may change and be upgraded with hardware updates. For further information, see the Help option on the App.

Pairing

Your phone with Bluetooth and WIFI must be ON for this step. Keep the screen lit with the radar icon showing .

Run the App CELLULARLINE-EASYFIT. The system will show the main page. Tap the button in the left corner or swipe the screen from left to right, and click [Device Connection]

Press the button on the bracelet twice. The "" radar icon will appear on the bracelet. Tap the [Searching device] button on the App, select your correct ID from the device list, and wait 1-2 seconds

If the pairing pop-ups do not appear within 1 minute, repeat the above steps. The Bluetooth icon may be shown instead of the Radar icon .

SYNC Data

The SYNC Data function automatically synchronises the bracelet after it is connected to your phone by the CELLULARLINE-EASYFIT App. The time on the bracelet is set to be the same as the time on the phone. SYNC Data includes steps, calorie, distance. Using the App, you can check whether SYNC Data has completed successfully. SYNC Data takes 1-2 minutes the first time it runs. SYNC Data can also be run manually by clicking the refresh button on the App. If data synchronization fails, disconnect the Bluetooth connection, reconnect and run SYNC Data again.

Sleep monitor

To turn on the Sleep Mode: Slide to the moon icon and hold your finger down on the icon until the band shakes. When the time and moon icon appears, the band is in the sleep mode.

To exit the Sleep Mode: Hold your finger down on the screen to turn it on, and hold your finger down on the screen again until the band shakes. When the moon icon disappears and the original icon with the time reappears, the band has exited the sleep mode.

Auto sleep mode

Turn on the sleep mode by setting. The band will check whether the sleep mode has been set during the period 8:00 PM – 9:00 AM

Searching for the mobile phone

Hold your finger down on the phone icon until the band shakes. The mobile phone search function will ring the phone if it is in the ringing mode or will shake the phone once if it is in the vibrate mode.

Sedentary reminder

Open the Sedentary reminder and set the time interval using the Sedentary reminder setting. The time setting should be a valid time interval, such as 9:00-17:00 instead of 9:00-5:00. The Sedentary reminder mode will then be entered successfully. The band will shake and show the sedentary icon if it is kept motionless for one hour.

Alarm clock

Add an alarm using the Alarm setting function. At the programmed time, the band will shake as a reminder, and the alarm icon will appear.

Remote controller for camera

Open the camera using the App. The band will display the camera icon . The remote controller for the camera can now be activated by holding your finger down on the icon.

Calling and message reminder

Check the push reminder and open all notification items. Now, reset your SMS notification and choose Message.

If you are unable to receive notifications when the band is connected to the mobile phone, disconnect the band from the phone, exit the notification function, then re-open the function.