FIBARO YH-001, HC3L-001 - Yubii Home Center Manual
![]()
![]()
Read this manual carefully before installing and operating the product.
![]()
- The manufacturer will not be held responsible for any loss or damage resulting from not following the instructions. Store this manual in a secure place for future reference.
- This product is not a toy. Keep away from children and animals.
- When wall-mounted, do not place the product higher than 2 meters from the floor.
![]()
- Do not attempt to disassemble, repair or modify this product yourself. Any repair should be performed only by an authorized FIBARO service.
- This product is designed for indoor use only. Do not use outside!
- Do not expose this product to moisture, water, or other liquids. Never place any water carrying vessels near the product.
- Do not use the product outside of the recommended temperature and humidity ranges.
- Keep the product away from heat sources and do not place under direct sunlight.
- Do not cover or place anything on the product.
- Do not connect cable longer than 3 meters to the USB port.
- Do not place the product in metal boxes or on metal surfaces for best radio performance.
Installation
- Plug the provided power adapter into an outlet and connect it to the gateway.
- The gateway will turn on, wait for the indicator to turn solid red.
- Connect your computer to Wi-Fi network created by the gateway. You will find Wi-Fi SSID (name) and password on the bottom of the device.
First configuration
- Go to find.fibaro.com or 10.42.0.1.
- Choose your language.
- Login with default credentials:
- Login: admin
- Password: admin
- Configure the gateway by following steps in the Configuration Interface.
Remember: connect the gateway to your home Wi-Fi network after finishing the configuration.
Remote access
To control the gateway outside your house:
- Go to id.cloud.fibaro.com.
- Create an account.
- Go to Remote Access and add your gateway.
Status indicator
Pulsing blue – start-up
Red – Wi-Fi in Access Point mode (ready to configure)
Pulsing red – disconnected from Internet
Green – connected to the Internet
Pulsing red – start-up to Recovery mode
R - Reboot
Hold for 5s – restart
D - Recovery
Hold during start-up – put in Recovery mode
Hold for 10s, then click when the indicator is blinking – switch between Dynamic and Static IP:
- yellow blinking: set IP to Dynamic
- green blinking: set IP to Static
Hold for 20s, then click when the indicator is blinking red – reset network settings
Technical specifications
Model number | YH-001 HC3L-001 |
Power supply | 5 V DC, max. 1 A (adapter included) |
Operating temperature | 0-40°C |
Operating humidity | max. 75% relative humidity (non-condensing) |
Power connector | USB Micro B |
Dimensions | 178x110x31 mm |
Radio communication
Protocol | Radio frequency | Max. transmitting power |
Z-Wave (700 series) | 868.0-868.6 MHz * 869.7-870.0 MHz * | +9 dBm |
Wi-Fi (802.11 b/g/n) | 2400.0-2483.5 MHz | +20 dBm |
433 Mhz (YH-001 only) | 433.05-434.04 Mhz | +9 dBm |
868 Mhz (YH-001 only) | 868.0-869.65 MHz | +5 dBm |
* Given frequencies are only for the European Union device version. For other device versions, local regulations apply.
WEEE Directive Compliance
![]()
Device labelled with this symbol should not be disposed with other household wastes. It shall be handed over to the applicable collection point for the recycling of waste electrical and electronic equipment.
![]()
Hereby, Fibar Group S.A. declares that the device is in compliance with the essential requirements and other relevant provisions of Directives 2014/53/EU, 2011/65/EU and 2015/863. The full text of the EU declaration of conformity is available at the following internet address: manuals.fibaro.com
![]()
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download FIBARO YH-001, HC3L-001 - Yubii Home Center Manual
Need help?
Do you have a question about the YH-001 and is the answer not in the manual?
Questions and answers