Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for U-Line U-CLR1215S-40B
Summary of Contents for U-Line U-CLR1215S-40B
- Page 1 QUICK START GUIDE 1000 Series CLR1215 115 V / 60 Hz • •...
- Page 2 1. U-Line Customer Care must be contacted immediately at +1.800.779.2547. 2. Service or repairs performed on the unit without prior written approval from U-Line is not permitted. If the unit has been altered or repaired in the field without prior written approval from U-Line, claims will not be eligible.
-
Page 3: Table Of Contents
QUICK START GUIDE u-line.com Contents Model List Safety and Warning Environmental Requirements Electrical Water Hookup Drain Door Swing General Installation Integrated Panel Installation Control Operation First Use Sabbath Mode Warranty... -
Page 4: Model List
QUICK START GUIDE u-line.com Model List This guide provides the basics to get you started. Looking for more information? Visit u-line.com to view detailed User Guides for all U-Line products. Clear Ice U-CLR1215S-00B U-CLR1215S-40B U-CLR1215INT-00B U-CLR1215INT-40B U-CLR1215B-00B U-CLR1215B-40B U-CLR1215W-00B U-CLR1215W-40B... -
Page 5: Safety And Warning
QUICK START GUIDE u-line.com Safety and Warning This unit is designed to operate between 50°F (10°C) and 100°F (38°C). Higher ambient temperatures may reduce NOTICE the unit’s ability to reach low temperatures and/or reduce ice production on applicable models. Please read all instructions before installing, operating, or servicing the appliance. -
Page 6: Electrical
QUICK START GUIDE u-line.com Electrical Water Hookup INDOOR MODELS WARNING PREPARE PLUMBING Please use the braided stainless steel water supply line SHOCK HAZARD — Electrical Grounding which comes attached. The water line is fitted with a Required. Never attempt to repair or perform standard 1/4"... - Page 7 QUICK START GUIDE u-line.com 3. Locate braided stainless steel CAUTION water supply line and connect to your cold water supply. The Do not use any plastic water supply line. The line water line should be looped into is under pressure at all times. Plastic may crack 2 coils.
- Page 8 The water valve uses a standard 1/4" (6.35 mm) Do not use any plastic water supply line. The line compression fitting. U-Line recommends using accessory is under pressure at all times. Plastic may crack water hook up kit – part # WATERHOOKUP. The kit...
- Page 9 QUICK START GUIDE u-line.com 3. Locate water 8. Install retaining clip. valve in the front of the unit and thread water supply line through. NOTICE Route the water supply line through the unit so it does not come into contact with any internal components other than the solenoid valve.
-
Page 10: Drain
DRAIN CONNECTION CAUTION With Trap and Vent Proper Drain If your U-Line unit did not come with a factory installed drain pump you must use a gravity A gravity drain may be used if: style drain connection. For assistance in Drain line has at least a 1"... -
Page 11: Door Swing
(Optional Hook-Up) requirements for a gravity drain, you may have ordered a pre-installed U-Line P60 drain pump. Waste If you need to install a P60 drain pump into your unit, see Valve DRAIN PUMP section in the User Manual. -
Page 12: General Installation
QUICK START GUIDE u-line.com General Installation INSTALLATION 1. Plug in the power/electrical cord. LEVELING INFORMATION 1. Use a level to 2. Gently push the unit into position. Be careful not to confirm the unit is entangle the cord or water and drain lines. - Page 13 A adjust panel as necessary. Tighten screws upon robust tape may also completion. be used. U-Line recommends the use of bar clamps to 15.Starting at the corners, re-install the gasket into the Door/Drawer secure the panel to gasket channel in the frame.
-
Page 14: Control Operation
”. 3 hours) Clean Mode Hold for five seconds First Use All U-Line controls are preset at the factory. Initial startup ICE CUBE THICKNESS ADJUSTMENT requires no adjustments. NOTICE Ice thickness adjustment should only be made NOTICE one increment at a time. Allow ice maker... - Page 15 QUICK START GUIDE u-line.com The ice cube thickness is factory set for best overall Your clear ice machine is pre-set to produce ice between performance. The factory setting is designed to maintain the optimal dimensions illustrated below: an ice bridge of approximately 1/16" to 1/8" (1.6 mm to Cube Details 3.2 mm) under normal conditions, resulting in a dimple of...
-
Page 16: Sabbath Mode
U-Line further warrants the sealed system (consisting of the compressor, condenser, evaporator, hot gas bypass valve, dryer, and connecting tube) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of Select installation. - Page 17 U-Line shall have no liability whatsoever for any incidental, consequential, or 5. U-Line products are designed to operate in ambient special damages arising from the sale, use, or temperatures between 50°F and 100°F unless installation of the product or from any other cause otherwise noted in the product manual.