Assembly - Mr. Heater MH480FAET Operating Instructions And Owner's Manual

NEVER LEAVE THE HEATER UNATTENDED WHILE OPERATING! NEVER LEAVE THE HEATER UNATTENDED WHILE OPERATING! NEVER LEAVE THE HEATER UNATTENDED WHILE OPERATING!

Assembly

Installation:
&
Wall Mount Application
Tools­Needed:
•­ Power­Drill
•­ 4mm­or­5/32in.­drill­bit
•­ Phillips­Head­Screwdriver
WARNING:­USE­THIS­HEATER­ONLY­AS­DESCRIBED­IN­THIS­
MANUAL.­­ANY­OTHER­USE­NOT­RECOMMENDED­BY­THE­
MANUFACTURER­IS­STRICTLY­PROHIBITED­AND­MAY­CAUSE­
FIRE,­ELECTRIC­SHOCK,­OR­INJURY­TO­PERSONS.
•­ Remove­the­heater­and­all­of­the­packaging­material­from­
the­box.
•­ Make­sure­to­remove­the­hardware­package­from­the­
styromfoam­packaging.
•­ Check­all­of­the­packing­material­for­loose­parts­and­set­
aside.
•­ Thoroughly­inspect­the­heater­for­damage.­If­any­is­found­
do­not­contact­the­place­of­purchase.­Please­call­the­
Manufacturer­at­800-251-0001.
Attaching Heater to Wall/Ceiling
1.­ Line­up­both­holes­on­the­bracket­with­the­holes­on­the­
heater­handle.
2.­ Attach­the­heater­to­the­bracket­with­the­20mm­screw­and­
nut,­10mm­washer,­and­locking­washer.
3.­ Locate­wood­stud­in­wall­or­joist­in­ceiling­to­mount­heater.­
The­selected­space­should­leave­enough­room­to­maintain­
the­clearance­to­combustibles­outlined­in­the­specifications­
table­on­page­3.
Grounding Instructions:
The­heaters­covered­in­this­manual­are­designed­to­be­installed­and­
serviced­by­only­licensed­trained­professionals.­­Heaters­should­only­
be­installed­on­a­dedicated­240­volt­circuit.­The­cord­has­a­plug­as­
shown­below.­No­adapter­is­available­for­this­blade­configuration,­and­
Mr. Heater Forced-Air Electric Workspace Heater
Figure­2
Ceiling Mount Application
4.­ Use­holes­in­the­bracket­to­mark­holes­for­drilling.
5.­ Once­holes­have­been­marked,­pre-drill­2­holes­for­screws.
6.­ Secure­two­65mm­screws­to­the­wall/ceiling­joist,­leaving­
1/8'­exposed.­The­two­screws­must­be­attached­securely­to­
a­wood­stud­(min.­1.5").
7.­ Mount­the­heater­by­attaching­the­bracket­to­the­exposed­
screw­heads­by­sliding­through­the­keyholes­on­the­bracket­
and­pushing­down­to­lock­the­bracket­into­place.­It­is­
recommend­that­you­have­help­for­this­step.
8.­ Tighten­the­screws­against­the­bracket­to­secure.
WARNING:­Heater­must­be­attached­to­a­joist­with­minimum­
of­(2)­screws­in­opposing­holes.
WARNING:­Use­appropriate­fasteners.­­The­screws­included­
are­for­installing­in­wood­studs­only­and­are­not­intended­for­
metal­joists.
WARNING:­Be­certain­adjustment­screws­are­tightened­firmly­
to­secure­heater­to­bracket.
SAVE THESE INSTRUCTIONS
IMPORTANT:­­Read­all­instructions­and­warnings­carefully­before­
installation­and­use.­­Failure­to­follow­these­instructions­may­result­
in­a­possible­electric­shock,­injury­to­persons,­fire­hazard­and­will­
none­should­be­used.­The­type­outlets­a­240­(208)­volt­grounding­
outlet.­When­properly­installed­It­provides­a­ground­connection­
through­the­cord­to­the­heater­to­prevent­the­operator­from­electric­
shock.­Be­sure­that­the­electrical­receptacle­is­of­the­configuration­
and­capacity­appropriate­for­the­heater.
Figure­3
4
Operating Instructions and Owner's Manual
void­the­warranty.