3M Speedglas 9100 FX Air Care & Maintenance

Care & Maintenance
3M Speedglas
™
To optimise the effective lifetime of your welding equipment and avoid the additional cost of replacement, regular
maintenance is important. Replace all damaged parts immediately to ensure correct levels of protection.
Before use
• Helmet and head harness. Inspect for cracks or
any damaged or defective parts. Replace if needed.
• Cover lenses and visor. To provide the best possible vision
they should be clean and without scratches.
• Face seal. If the face seal is damaged there is a great
risk that contaminated air will get inside the helmet.
Verify it's in position and free from splits and tears.
• Welding lens. Ensure low battery is not flashing
and check that the sensors are clean and uncovered.
• Breathing tube. Confirm tube is not damaged or
leaking any air. To extend the life of breathing tube,
use a tube cover or a heavy-duty rubber tube.
16 95 02
16 95 05
16 95 50
53 61 00
53 30 00
79 01 01
Part No Description Part No
169006 HEAD COVER SMALL 9100 FX 171020
169007 HEAD COVER LARGE 9100 FX 171021
169010 THROAT PROTECTION 9100 171022
169100 HEAD CAPE TECAWELD 171023
169502 SWEATBAND 9100 & 9100 FX PK=2 171024
169505 SWEATBAND 9100 & 9100 FX PK=5 422000
169550 SWEATBAND 9100 & 9100 FX PK=50 500026
Unit 13, 39 Herbert Street • St Leonards NSW 2065 • Australia
Welding Helmet 9100 FX Air
™
After use
• Clean the helmet. Wipe with a moist tissue or cloth, both inside and
outside the helmet. If you suspect that the inside of the airduct is dirty,
it must be changed.
DO NOT rinse, immerse in water or clean with solvents.
• Face seal and sweatband. Remove for additional cleaning
as needed and replace if they become unhygienic.
• Cover lenses and visor plate. Clean with a soft cloth
and replace if any pits or scratches occur.
• Breathing tube. Replace if damaged, deformed or leaking any air.
• Storage. Store the helmet in a dry, clean area away from direct
sunlight, high temperatures and solvents.
53 60 00
53 62 00
52 30 00
54 05 00 52 30 01
54 28 00
Description Part No Description
LENS MAGNIFYING 1.0X 9100 100 & 9000 523000 VISOR PLATE 9100 FX PK=5
LENS MAGNIFYING 1.5X 9100 100 & 9000 523001 VISOR PLATE ANTI-FOG 9100 FX PK=5
LENS MAGNIFYING 2.0X 9100 100 & 9000 526000 LENS COVER OUTER STD 9100 PK=10
LENS MAGNIFYING 2.5X 9100 100 & 9000 527000 COVER LENS OUTER HC 9100 PK=10
LENS MAGNIFYING 3.0X 9100 100 & 9000 527070 LENS COVER OUTER HT 9100 PK=10
BATTERY LITHIUM 9100, 100 & 9000 PK=2 528025 LENS COVER INNER 9100XX PK=5
LENS WELDING 9100XXi SPEEDGLAS 531000 HOLDER BATTERY 9100
Authorised 3M Wholesaler
T: (02) 9439 0111 • F: (02) 9439 0100
E: sales@awsi.com.au
W: www.speedglas.com.au
16 90 06
42 20 00
53 35 00
52 60 00
53 10 00
52 70 00
53 40 00
52 70 70
53 20 16
53 50 00
Part No Description
532016 SIDEWINDOWS COVER PLATE 9100 FX PK=2
533000 HEAD HARNESS 9100
533500 AIR DUCT ASSEMBLY 9100 FX AIR
533505 ADAPTOR ADFLO BREATHING TUBE 9100 FX AIR
534000 FACE SEAL 9100 FX AIR
535000 AIR DEFLECTOR 9100 FX AIR
536000 HEAD HARNESS PIVOT MECHANISM 9100
Further information and advice
To request a quote or place an order for spare parts, please contact TWS on +61 (0) 7 4659 0044 or visit www.tweld.com.au. Please note that higher than normal levels
of pollutants, heat and sparks will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our
YouTube Channel (www.youtube.com/user/3MSpeedglas) or contact your local TWS representative.
53 35 05
52 80 25
16 90 07
17 10 20
17 10 21
17 10 22
17 10 23
50 00 26 17 10 24
Part No Description
536100 HEAD HARNESS FRONT PART 9100
536200 HEAD HARNESS BACK PART 9100
540500 FRONT COVER KIT 9100 FX
542800 HELMET WELDING 9100 FX AIR EXC LENS
790101 CARRY BAG SPEEDGLAS
16 91 00
16 90 10