3M Speedglas 9100 Air Series Care & Maintenance

Care & Maintenance
3M Speedglas
™
To optimise the effective lifetime of your welding equipment and avoid the additional cost of replacement, regular
maintenance is important. Replace all damaged parts immediately to ensure correct levels of protection.
Before use
• Helmet and head harness. Inspect for cracks or any
damaged or defective parts. Replace if needed.
• Cover lenses. To provide the best possible
vision they should be clean and without scratches.
• Face seal. If the face seal is damaged there is a great
risk that contaminated air will get inside the helmet.
Verify it's in position and free from splits and tears.
• Welding lens. Ensure low battery is not flashing
and check that the sensors are clean and uncovered.
• Breathing tube. Confirm tube is not damaged or
leaking any air. To extend the life of breathing tube,
use a tube cover or a heavy-duty rubber tube.
52 80 25
42 20 00
52 60 00 50 00 26
52 70 00
53 10 00
52 70 70
Part No Description Part No
169005 HEAD PROTECTION 9100 171021
169010 THROAT PROTECTION 9100 171022
169100 HEAD CAPE TECAWELD 171023
169502 SWEATBAND 9100 & 9100 FX PK=2 171024
169505 SWEATBAND 9100 & 9100 FX PK=5 422000
169550 SWEATBAND 9100 & 9100 FX PK=50 500026
171020 LENS MAGNIFYING 1.0X 9100 100 & 9000 502800
Unit 13, 39 Herbert Street • St Leonards NSW 2065 • Australia
Welding Helmet 9100 Air
™
After use
• Clean the helmet. Wipe with a moist tissue or cloth,
both inside and outside the helmet. If you suspect that the inside
of the airduct is dirty, it must be changed.
DO NOT rinse, immerse in water or clean with solvents.
• Face seal and sweatband. Remove for additional cleaning as needed
and replace if they become unhygienic.
• Cover lenses. Clean with a soft cloth and replace if any pits or
scratches occur.
• Breathing tube. Replace if damaged, deformed or leaking any air.
• Storage. Store the helmet in a dry, clean area away from direct
sunlight, high temperatures and solvents.
16 91 00
16 90 10
17 10 20
17 10 21
17 10 22
17 10 23
17 10 24
Description Part No
LENS MAGNIFYING 1.5X 9100 100 & 9000 526000
LENS MAGNIFYING 2.0X 9100 100 & 9000 527000
LENS MAGNIFYING 2.5X 9100 100 & 9000 527070
LENS MAGNIFYING 3.0X 9100 100 & 9000 528025
BATTERY LITHIUM 9100, 100 & 9000 PK=2 531000
LENS WELDING 9100XXi SPEEDGLAS 532100
HELMET WELDING 9100 AIR EXC LENS 533000
Authorised 3M Wholesaler
T: (02) 9439 0111 • F: (02) 9439 0100
E: sales@awsi.com.au
W: www.speedglas.com.au
16 95 02
16 95 05
16 95 50
53 61 00
53 30 00
Description Part No Description
LENS COVER OUTER STD 9100 PK=10 533505 ADAPTOR ADFLO BREATHING TUBE 9100 AIR
COVER LENS OUTER HC 9100 PK=10 533700 AIR DUCT BACK PART 9100 AIR
LENS COVER OUTER HT 9100 PK=10 534100 FACE SEAL 9100 AIR
LENS COVER INNER 9100XX PK=5 536000 HEAD HARNESS PIVOT MECHANISM 9100
HOLDER BATTERY 9100 536100 HEAD HARNESS FRONT PART 9100
COVER FRONT SILVER 9100XXi 536200 HEAD HARNESS BACK PART 9100
HEAD HARNESS 9100 790101 CARRY BAG SPEEDGLAS
Further information and advice
To request a quote or place an order for spare parts, please contact TWS on +61 (0) 7 4659 0044 or visit www.tweld.com.au. Please note that higher than normal levels
of pollutants, heat and sparks will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our
YouTube Channel (www.youtube.com/user/3MSpeedglas) or contact your local TWS representative.
16 90 05
53 60 00
53 62 00
53 21 00
53 37 00 53 41 00
50 28 00
53 35 05
79 01 01